Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
сл 0 з ф ф_ 1 ф - S о ф г+ 3 3. ф ^ a с I? о» "1 ш g 3 О. , СЛ г* ч -< 3- о 5Г£= Ф о ш о з — сл rt. сл 3* “ а О С сл' ® 8 »г1 | z d* с С о — 3 Г*” сл 3 ^ Ф 1. о С û> ^ ^ 3 о т сл #л* ^ сл ф 3 13 ш ТЗ ™ ф - CL -, д. ы. о 2_ - СЛ* о Ф 3 ф ф a о О f- ш ~ — ш сл г- %< т сл Ф 3- 3 о ■ 7Г 3 ф сл т о о о с CD г- 7> g с g S-"в о < С Ф ь ч о S. о -с J Û) 2 о. 0 Ф ю °-а> ф 1 а. 3 а аГ'? Blacks. Decker, jig saw. SWITCH METAL CUTTING FIGURE 1 F16U1E 2 FIGURE 3 Push the Switch Button forward to turn the saw “ON”. As you push the button forward it will first click into a position exposing the letters “LO” (Figure 1). This is the low speed position for cutting metals and plastics. Pushing the button farther forward until it clicks again will expose the letters “HI” (Figure 2). This is the high speed position for cutting woods and composition boards. Pulling the switch button all the way back turns the tool “OFF” (Figure 3). BEVEL ADJUSTMENT The Jig Saw Shoe may be tilted to permit bevel cutting at any angle from 0° to 45°. To change the angle of the shoe, loosen screw (see above) and tilt shoe to desired cutting angle with blade. Retighten screw. Cutting angles of 0° and 45° are indicated on the left side, raised portion of shoe when viewed from rear of saw, IP1 WOOD CUTTING Be sure board is firmly positioned. Hold Jig Saw by the convenient overhead handle and operate switch to turn the unit on. Don't attempt to turn on when blade is against material to be cut. This could stall the motor. Place front of shoe on material to be cut and hold Jig Saw shoe down firmly against the wood while cutting. Don't force the tool; let the blade. cut at its own speed. Whenever possible, clamp or support work close to the line of cut; when the cut is completed, shut off power and lay the saw aside before loosening the work. CAUTION: When sawing into walls, floors or wherever “live” electrical wires may be encountered, DO NOT TOUGH ANY METAL PARTS OF THE TOOL! Hold the Jig Saw only by its plastic handle to prevent electric shock if you saw into a “live" wire. In cutting thin gage sheet metals it is best to clamp wood or plywood to bottom of metal sheet, this will insure a clean cut without the danger of vibration or tearing of metal. Always remember to use a finer blade for ferrous metals (those that have an iron content). Use a coarser blade for non-ferrous metals (those that do not have an iron content). POCKET CUTTING A pocket cut is an easy method of making an inside cut. The saw can be inserted directly into a panel or board without first drilling a lead or pilot hole. In pocket cutting measure the surface to be cut and mark clearly with a pencil. Next tip the saw forward until the front edge of the shoe sits firmly on the work surface. Switch the tool on and allow it to attain maximum speed. Grip the handle firmly and lower the back edge of tool until the blade cuts smoothly into material. Always be sure blade reaches its complete depth before starting to cut. RIP & CIRCLE CUTTING CIRCLE CUTTING Ripping and circle cutting without a pencil line are easily done with the No. U-2151 Accessory lip Fence and Circle Guide. (The attachment of this Accessory is explained in the drawing below.) When-ripping; insert rip fence in either side of saw; adjust to width of cut and tighten thumb screw. When circle cutting, insert rip fence from either side with cross bar facing up; adjust rip fence so that distance from blade to hole in cross bar is the desired radius and tighten thumb screw; place saw so that center of hole in cross bar is over center of circle to be cut (make pocket cut, drill hole for blade or cut inward from edge of material to get blade into position). When saw is properly positioned, drive a small nail through hole of cross-bar into exact center of circle to be cut. Using rip fence as a pivot arm, begin cutting circle. The Nut and Thumb Screw shown above are included with this Accessory. Hold the nut in the position shown and thread the thumb screw into it just enough to hold the nut loosely in position. Pull up on the thumb screw and slide the Rip Fer^ce under the nut from either side of the Saw. Set the cross bar at desired distance from blade and tighten thumb screw. For ripping the cross bar should be down as shown. For circle cutting the cross bar should be up. JIG SAW BLADES iiiiiiiiii iilillliilliiiiiiiiiiiiiii ¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡■¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡¡il of^Cut llllillllllllli IliiiiiBilllillll i Teeth Per Inch | IlllliSllIl ¡¡liiiiiii 1 B&D 1 Cat. i No. ICO is-___^nd hard 1 ■ | Rough II liiiiiii 1 | 7 1 IIIIIIIIIIIIIIIIIIIIII Jlllllll i 54368 | Medium ;|||||liiil||i 1 10 IIIIIIIIIII1IIIIIIIIIII 54369 i Smt'o'cl? ;ii|||li|||i| ■ V llllillllllllli 54370 | Smooth ¡llilllllillil 10 ¡IIIIIIIIII!!!!!! 39754 SrfsCOt h ¡i^iiiiiiiii s 39755 | Smooth ¡¡¡lliillllllli | a liiiiiiiiiiiiii 39756 C'- v ><- 'oOs1 n...
Эта инструкция также подходит к моделям:Лобзики и пилы - 722066 (3.74 mb)