Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY. 5 SCROLL SAW PARTS 1 2 3 4 5 6 7 8 9 10 11 Fig. 1 Fig. 2 Fig. 1 Fig. 2 1. Scroll Saw with blade attached 2. Table 3. Quickset Blade Changing Wrench 4. Holddown Rod 5. 4mm Hex Wrench 6. Locking Handle 7. M10 Flat Washer 8. Blank Table Insert 9. Table Insert 10. Special Screw M6x1x45mm (2) 11. M6 Locknut (2) ASSEMBLY WARNING: For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. ASSEMBLY TOOLS REQUIRED 1.) 4mm hex wrench - supplied 3.) 10mm wrench 2.) Quickset Blade Changing Wrench - supplied ASSEMBLY TIME ESTIMATE Less than one hour 6 1. Remove the blade from the scroll saw. 2. Move the blade lever tension handle (A) Fig. 3, to the foreword position as shown. A Fig. 3 3. Push chuck locking lever (B) Fig. 4 to the rear as shown. This will release the blade (C) from the upper chuck assembly (D). B C D Fig. 4 4. Insert long end (F) Fig. 5, of quickset blade changing wrench into hole (G) in lower blade holder. This will align wrench (H) with blade holder screw (J). Turn wrench (H) counter-clockwise. This will release the blade from the lower chuck assembly. Fig. 5 FG HJ 5. Position table (A) Fig. 7, on the machine as shown. Align the two holes in the table trunnions (O) with the two holes in the base (P) of the machine. NOTE: BEFORE TIGHTENING THE M6x1x45mm SPECIAL SCREWS (B) AND M6 LOCKNUTS (C) FIG. 7, MAKE SURE THE TILT SCALE (D), IS POSITIONED INSIDE POINTER (E) AS SHOWN. ALSO, DO NOT COMPLETELY TIGHTEN THE M6x1x45mm SPECIAL SCREWS (B) AND M6 LOCKNUTS (C). TABLE MUST BE ABLE TO TILT FREELY. Fasten the table (A), to the base (P), using the two M6x1x45mm special screws (B), and M6 locknuts (C) as shown. Fig. 7 B P O C A C O B P D E 7 6. Disassemble the handle by unscrewing and re mov ing screw and spring (F), and handle (G) from locking stud (H), as shown in Fig. 8. Place a M10 flat washer (J) on threaded end of stud (H). Fig. 8 F G H J 7. Screw threaded end of stud (H) Fig. 9, with the M10 flat washer (J) through slot in angle of tilt scale (D) and into tapped hole (K). Fig. 9 J H D K 8. Place handle (G) Fig. 10, onto locking stud (H) and fasten with screw and spring (F). Move table (A) to the horizontal position and lock table (A), by turning handle (G) clockwise. Fig. 10 GF H A 9. Using the 4mm wrench (L) Fig. 11, loosen the two screws (P) on bottom of bracket (M) that fasten bracket to rod (N). NM P L Fig. 11 8 10. Rotate bracket (M), to the position shown in Fig. 12. Loosen lock handle (R) and insert holddown rod (S) into hole in bracket (M), as shown. R M S Fig. 12 11. Rotate bracket (M) Fig. 13, back to its original position as shown, and tighten the two screws that were loosened in STEP 9. Then tighten lockhandle (R) to hold rod (S) in position. Fig. 13 M N S R 12. Slide end of chip blower tube (T) Fig. 14, onto end of air nozzle (V), as shown. T V Fig. 14 13. The tool holder (X) Fig. 15, is used to hold the quickset blade changing wrench (Y), (for removing blade from lower blade holder), 4mm allen wrench (W) and extra blades (Z). Fig. 15 X Y W Z 9 FASTENING SCROLL SAW TO SUPPORTING SURFACE WARNING: Your scroll saw MUST be securely fastened to a stand or workbench using the holes in the four rubber feet, three of which are shown at (A) Fig. 16. IMPORTANT: When mounting the saw to a stand or workbench DO NOT over-tighten mounting bolts. Leave some cushion in the four rubber feet (A) for absorbing noise and vibration. An alternate method of securing the scroll saw is to clamp the front and side ledges of the scroll saw to a supporting surface with C-clamps. IMPORTANT: If there is any tendency for the stand or workbench to move during operation, the stand or work-bench must be fastened to the floor. OPERATING CONTROLS AND ADJUSTMENTS ON-OFF AND VARIABLE SPEED SWITCHES The on-off switch (A) Fig. 17, and variable speed switch (B) is located on the right side of the scroll saw base, as shown. To turn the saw "ON," push the switch (A) up to the “ON” position. To turn the saw "OFF", push the switch (A) down to the “OFF” position. The scroll saw is equipped with a variable speed control knob (B) Fig. 17. The variable speed range is 400 to 1800 strokes per minute. When the variable speed knob is rotated all the way to the left (counterclockwise) the speed will be 400 strokes per minute. To increase the speed, rotate knob (B) to the right (clockwise) until the desired speed is obtained. When the knob (B) is rotated all the way to the right (clockwise) the speed will be 1800 strokes per minute. LOCKING ON-OFF SWITCH IN THE "OFF" POSITION IMPORTANT: When the machine is not in use, the ...
Эта инструкция также подходит к моделям:Лобзики и пилы - BDSS100 (388.23 kb)