Оценок - , средний балл:
(
)
)
Производитель: Black & Decker
Размер: 461.37 kb
Название файла: 2e60cf78-8c01-4929-b1a3-1fdc8997fa6c.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
• Always hold saw firmly with both hands while cutting as shown in Figure 3. Whenever possible, the saw shoe must be held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage. TRIGGER SWITCH (FIGURE 4) Release lock-off by switching to the unlocked position shown in Fig. 4 from either side of the saw. Pull the trigger switch to turn the motor ON. Releasing the trigger turns the motor OFF. NOTE: This tool has no provision to lock the switch in the ON position, and should never be locked in the ON position by any other means. BLADE CLAMP RELEASE LEVER (FIGURE 5) CAUTION: TURN OFF AND REMOVE BATTERY FROM TOOL. To install blade into saw: 1. Open blade clamp release lever to its full open position as shown in Figure 5. 2. Insert blade shank from the front. 3. Close blade clamp release lever. To remove blade from saw: 1. Open blade clamp release lever to its full open position. 2. Remove blade. FLUSH CUTTING (FIGURE 6) • The compact design of the reciprocating saw motor housing and pivoting shoe permit close cutting to floors, corners and other difficult areas. • To maximize flush cutting capabilities, insert the blade shaft into the blade clamp with the teeth of the blade facing up. • Turn the saw upside down so you are as close to the work surface as possible. WOOD CUTTING (FIGURE 7) • Before cutting any type of wood, be sure the work piece is firmly anchored or clamped to prevent slipping. • Place blade and shoe lightly against work to be cut. • Switch on saw motor before applying pressure. • Always hold saw firmly with both hands while cutting. Whenever possible, the shoe must be held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage. METAL CUTTING • Use a finer blade for ferrous metals and a coarse blade for non-ferrous materials. • In thin gauge sheet metals it is best to clamp wood to both sides of sheet. This will ensure a clean cut without excess vibration or tearing of metal. • Avoid forcing cutting blade as this reduces blade life and causes costly blade breakage. NOTE: You should spread a thin film of oil or other coolant along the line ahead of the saw cut for easier operation and longer blade life. For cutting aluminum, kerosene is preferred. POCKET CUTTING - WOOD ONLY (FIGURE 8) • Measure the surface area to be cut and mark clearly with a pencil, chalk or scriber. • Insert pocket cutting blade in blade clamp and tighten blade clamp securely. • Tip the saw backward until the back edge of the shoe is resting on the work surface. • Switch motor on, permitting blade to attain maximum speed. • Grip handle steadily and begin a slow, deliberate upward swing with the handle of the saw. • The blade will begin to feed into material. Always be sure blade is completely through material before continuing with pocket cut. NOTE: In areas where blade visibility is limited, use the edge of the shoe as a guide. PROJECT TIPS • Cut only with sharp blades; they cut cleaner, faster and put less strain on the motor while cutting. • When cutting, always ensure that the shoe is resting against the workpiece. This will improve operator control and minimize vibration. • For longer blade life, use bi-metal blades. These utilize a carbon steel back welded to high speed steel teeth making the blade more flexible and less prone to breaking. Troubleshooting Problem Possible Cause Possible Solution • Unit will not start. • Battery not installed properly. • Check battery installation. • Battery not charged. • Check battery charging requirements. • Battery will not charge. • Battery not inserted into charger. • Insert battery into charger until red LED appears. • Charger not plugged in. • Plug charger into a working outlet. Refer to “Important Charging Notes” for more details. • Surrounding air temperature • Move charger and tool to too hot or too cold. a surrounding air temperature of above 40 degree F(4,5°C) or below 105 degree F (+40,5°C). For assistance with your product, visit our website for the location of the service center nearest you or call the BLACK & DECKER help line at 1-800-544-6986. MAINTENANCE REMOVE BATTERY FROM SAW WHEN PERFORMING ANY CLEANING OR OTHER MAINTENANCE. WHEN SERVICING USE ONLY IDENTICAL REPLACEMENT PARTS. • Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust etc. • When electric tools are used on fiberglass boats, sports cars, drywall etc.,they are subject to accelerated wear and possible premature failure, as the fiberglass chips and grindings and drywall dust are highly abrasive to bearings, brushes, commutator, etc. During any use on fiberglass or drywall it is extremely important that the tool be cleaned frequently by blowing with an air jet. LUBRICATION Your tool was properly lubricated before leavin...
Эта инструкция также подходит к моделям:Лобзики и пилы - Fire Storm FS2400RS (461.37 kb)