Войти:
Оценок - , средний балл: ( )

Инструкция по эксплуатации Black & Decker, модель 579795-00

Производитель: Black & Decker
Размер: 9.09 mb
Название файла: 13f55a00-916e-43e5-84ab-3cb246884190.pdf

Язык инструкции:enesfr

Документ загружается, подождите пожалуйста
Документ загружается, подождите пожалуйста

Фрагмент инструкции


To turn the too! off, release the trigger switch. The tool can be locked on for continuous operation by fully squeezing and holding the trigger switch while you depress the lock-on button shown in Fig. 3. With the lock-on button depressed, release the trigger switch and the tool will continue to run. To release from lock position, squeeze and release the trigger. Always disengage the lock before disconnecting from the power supply. VARIABLE SPEED SWITCH (JS200, JS300) BEFORE PLUGGING YOUR JIG SAW IN, ENSURE THAT THE TRIGGER SWITCH IS IN THE OFF POSITION. To turn the saw on, squeeze the trigger switch, as shown in Figure 3. The speed of the saw is determined by how much the trigger switch is depressed. To turn the tool off, release the trigger switch. The tool can be locked on for continuous operation by fully squeezing and holding the trigger switch while you depress the lock-on button shown in Fig. 3. With the lock-on button depressed, release the trigger switch and the tool will continue to run. To release from lock position, squeeze and release the trigger. Always disengage the lock before disconnecting from the power supply. Do not overload your jig saw as this could damage the motor. Use your saw only for its intended purpose. BEVEL ADJUSTMENT TURN OFF AND UNPLUG TOOL. ■ To adjust the bevel angle, loosen the screw (approximately 3 full turns) on the bottom of the shoe, as ' shown in Figure 1. Lift the shoe slightly and pull backward, then set the shoe at 45° and retighten screw. To reset the shoe for a square cut, loosen the screw and move the shoe until it is approximately 90° to the blade. Adjust the blade support roller to the blade and retighten the screw. GENERAL CUTTING Be sure board is firmly secured. Hold jig saw by the handle and operate switch to turn the unit on. Don’t attempt to turn on the unit when blade is against material to be cut. This could stall the motor. Place front of shoe on material to be cut and hold jig saw shoe down firmly against the work surface while cutting. Don’t force the tool; let the blade cut at its own speed. Whenever possible, clamp or support work close to the line of cut; when the cut is completed, shut off power and lay the saw aside before loosening the work. CUT LINE BLOWER To aid visibility when cutting, your jig saw is equipped with a cut line blower (Fig. 3) which will keep the work area clear of dust as you saw. BLADE STORAGE A convenient blade storage compartment (Fig. 3) is provided at the rear of the saw. METAL & PLASTIC CUTTING In cutting thin gauge sheet metals, it is best to clamp wood or plywood to the bottom of the metal sheet; this will insure a clean cut without the danger of vibration or tearing of metal. Use a fine-tooth blade for ferrous metals (for those that have an iron content); and use a coarser blade for nonferrous metals (those that do not have an iron content). Cutting thin metal will take longer than cutting relatively thick wood so do not be tempted to speed up the process by forcing the saw. Spread a thin film of cutting lubricant along the cutting line (any light weight oil). Use low speeds for cutting metals, plastics and composition tile. When cutting laminated plastic, place the finished side down and use a fine tooth hollow ground blade. , POCKET CUTTING • ' Measure the surface to be cut and mark clearly with a pencil. Next tip the saw forward until the front edge of the shoe sits firmly on the work surface, but with the blade well clear of it Figure 4. • Turn the tool on and allow it to attain maximum speed by fully depressing the trigger switch. • Grip the handle firmly and slowly lower the back edge of tool until the blade cuts smoothly into material. Do not move the jig saw forward along the cut line until the saw blade has completely entered the material and shoe comes to rest flat on its surface. RIP & CIRCLE CUTTING Ripping and circle cutting without a pencil line are easily done with the rip fence and circle guide (available at extra cost). Using the screw supplied with the accessory guide, position as shown in Figure 5 and thread the screw into the shoe to clamp the fence securely. When circle cutting, adjust rip fence so that distance from blade to hole in cross bar is at the desired radius and tighten screw (use hole which lines up best with saw blade). Place saw so that hole in cross bar is over center of circle to be cut (make pocket cut, drill hole for blade or cut inward from edge of material to get blade into position). When saw is properly positioned, drive a small nail through hole in cross bar. Using rip fence as a pivot arm, begin cutting circle. For circle cutting, the cross bar should be up, as shown in Figure 5. When ripping, slide the rip fence under the screw from either side of the saw. Set the cross bar at desired distance from blade and tighten screw. For ripping, the cross bar should be down and against the straight edge of the workpiece. MAINTENANCE ■ : - Use only m...

Эта инструкция также подходит к моделям:
Лобзики и пилы - 7552 (9.09 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории