Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
NOTE AND FOLLOW SAFETY INSTRUCTIONS THAT APPEAR ON THE FRONT OF YOUR TABLE SAW. Additional Safety Rules 12. THINK SAFETY WARNING! Some dust created by power sanding, SAFETY IS A COMBINATION OF OPERATOR COMMON sawing, grinding, drilling, and other SENSE AND ALERTNESS AT ALL TIMES WHEN THE construction activities contains chemicals known to TABLE SAW IS BEING USED. cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: WARNING! Do not allow familiarity (gained from fre-• Lead from lead-based paints, quent use of your table saw) to become • Crystalline silica from bricks and cement and othercommonplace. Always remember that a careless fraction of masonry products, and a second is sufficient to inflict severe injury. • Arsenic and chromium from chemically treated lumber. WARNING Wear Eye Protection Your risk from these exposures varies, depending on how The operation of any often you do this type of work. To reduce your exposure to power tool can result in these chemicals: work in a well ventilated area, and work foreign objects being with approved safety equipment, such as those dust thrown into the eyes, which masks that are specially designed to filter out microscopic can result in severe eye particles. damage. Always wear safety goggles that comply with ANSI Z87.1 (shown on package) before commencing power tool operation. Double Insulated Tools Double Insulation is a design concept used in electric WHEN SERVICING, USE ONLY IDENTICAL REPLACE- power tools which eliminates the need for the three wire MENT PARTS. grounded power cord and grounded power supply system. It POLARIZED PLUGS. If your tool is equipped with a polar- is a recognized and approved system by Underwriter’s Lab ized plug (one blade is wider than the other), this plug will fit oratories, CSA and Federal OSHA authorities. in a polarized outlet only one way. If the plug does not fit fully IMPORTANT: Servicing of a tool with double insulation re-in the outlet, reverse the plug. If it still does not fit, contact a quires care and knowledge of the system and should be qualified electrician to install the proper outlet. To reduce the performed only by a qualified service technician. risk of electric shock, do not change the plug in any way. WARNING! Extension Cords Replace damaged cords immediately. RECOMMENDED SIZES OF EXTENSION CORDS Use of damaged cords can shock, burn or 120 VOLT ALTERNATING CURRENT TOOLS electrocute. WARNING! Always use proper extension cord. If an extension cord is necessary, a cord with adequate size conductors should be used to prevent excessive voltage drop, loss of power or overheating. The table shows the correct size to use, depending on cord length and nameplate amperage rating of tool. If in doubt, use the next heavier gauge. Always use U.L. and CSA listed extension cords. Tool’s Ampere Rating Cord Size in A.W.G. Wire Sizes in mm2 25 50 100 150 Cord Length in Feet 15 30 60 120 Cord Length in Meters 3-6 18 16 16 14 .75 .75 1.5 2.5 6-8 18 16 14 12 .75 1.0 2.5 4.0 8-10 18 16 14 12 .75 1.0 2.5 4.0 10-12 16 16 14 12 1.0 2.5 4.0 — 12-16 14 12 —— — — — — NOTE: The smaller the gauge number, the heavier the cord. “SAVE THESE INSTRUCTIONS” 5. Table of Contents Page General Safety Rules.........................................................2 Additional Safety Rules..................................................3–5 Double Insulated Tools & Extension Cords .......................5 Table of Contents...............................................................6 Glossary of Terms..............................................................7 Tools Needed For Assembly..............................................7 Getting To Know Your Table Saw..............................20, 22 Power Switch ..............................................................20 Table ...........................................................................20 Base/Sub-Base ...........................................................20 Blade Bevel Lock Handle ............................................20 Table Extension ..........................................................20 Table Extension Lock Handle .....................................20 Elevation Wheel ..........................................................20 Blade Bevel Scale .......................................................20 Rip Fence Scale..........................................................20 Miter Gauge ................................................................20 Rip Fence Storage ......................................................20 Pre-Cut Locator...........................................................20 Miter Gauge Storage...................................................20 Blade Storage and Wrench .........................................20 Hex Wrench & Storage ...............................................20 Cord Wrap...................................................................20 Vacuum Hook-Up.................
Эта инструкция также подходит к моделям:Лобзики и пилы - 4100DG (2.97 mb)