Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
This unique mechanism brings you many benefits like the following: 1. Since the blade does not cause grass chips and pebbles to the thrown around, you may use less care about your clothing or surroundings. 2. Should the blade hit a rigid object like stones, trees or steel poles during operation, it does not produce a bounce motion that can cause loss of machine control. 3. Since the blade does not cause cut grass to wrap around the neck, you need not to stop operation to remove such wrappers. What's more, since the whole circle of the blade is available for cutting, you can move the cutting head in all directions and cut grass growing on such place difficult-toget with conventional trimmer. You can even trim the waterside without splashing water. HOW TO USE • Adjust the front handle to the most comfortable position. • Start the engine and pull the throttle trigger gradually. The blades will start moving as the engine speed goes up. •To stop the blade motion, simply release the throttle trigger. The clutch will disengage and the blades stop moving while the engine keeps idling. • Move the cutting head as sliding its bottom on the ground. This will help you do the job with less effort. SGCZ2600DL/SGCZ2600DW 8. Operation CUTTING WORK This machine does cutting not by a rotary cutter like conventional trimmers but by a pair of special blades that moves round within a limited angle at a speed of approximately 1/30 of conventional trimmers. This unique mechanism has brought you many benefits as following; 1. Since the blade does not cause grass chips and pebbles to be thrown around, you may use less care about your clothing or surrundings. 2. Should the blade hit a rogid object like stones, trees or steel poles during operation, it does not produce a bounce motion that can cause loss of machine control. 3. Since the blade does not cause cut grass to wrap around the neck, you need not to stop operation to remove such wrappers. 4. What's more, since the whole circle of the blade is available for cutting, you can move the cutting head in all directions and cut grass growing on such place difficult-to-get by conventional trimmers. You can even trim the waterside without splashing water. WARNING For your health and to prevent the risk from vibration, refrain from working for a long time at the cold temperature. • Road edge • Near fences •Around stones RECOMMENDED APPLICATIONS • Among trees • Parking area • Roadside •Waterside GB-12 SGCZ2600DL/SGCZ2600DW 9. Maintenance MAINTENANCE CHART System/components Procedure Before use Every 25 hours after Every 50 hours after Every 100hoursafter Note ENGINEfuel leaks, fuel spillage wipe out . fuel tank, air filter, fuel filter inspect/clean . . replace, if necessary idle adjusting screw see adjusting idling speed . replace carburetor if necessary spark plug clean and readjust plug gap . GAP: .025 in (0.6 ~ 0.7 mm) replace, if necessary cylinder fins, intake air cooling vent clean . muffler, spark arrester, cylinder exhaust port clean, remove piled up carbon . SHAFT throttle trigger, stop switch check operation . cutting parts replace if something’s wrong . angle transmission grease . screws/nuts/bolts tighten/replace . . except adjusting screws cutting attachment guard make sure to attach . G B • Before cleaning, inspecting, or repairing the unit, make sure that the engine has stopped and is cool. • Use protective gloves whenever inspecting, removing, sharpening, and installing the blades. BLADE Wipe off dust and dirt attached to the blades, and oil them after every use. To sharpen blade: 1. When the cutting edges have become dull, sharpen them by using a small disk grinder. (a) 2. When sharpening, offset the teeth of upper and lower blades by 3mm. (b) To offset, insert the hexagon wrench into the socket on the top of the angle transmission and rotate it. • Replace with new blades when the tooth width became less than 8mm at the tip. (c) • As the extent of wear differs by each tooth depending on use conditions, rotate the blade position at intervals. To remove blades: 1. Turn over the machine and remove the bottom cover (1) by removing the 4 screws. 2. Loosen 4 screws and remove the lower blade (2) 3. Loosen 4 screws and remove the upper blade (3). To install blades: The upper and lower blades are interchangeable. When fastening the blade mounting screws, torque them uniformly. GB-13 SGCZ2600DL/SGCZ2600DW 9. Maintenance WARNING Make sure that the engine has stopped and is cool before performing any service to the machine. Contact with moving cutting head or hot muffler may result in a personal injury. AIR FILTER • The air filter, if clogged, will reduce the engine performance. Check and clean the filter element in warm, soapy water as required. Dry completely before installing. If the element is broken or shrunk, replace with a new one. IMPORTANT • Note that using any spark plug other than those designated may result in the engine failing to operate properly or in the engine beco...
Эта инструкция также подходит к моделям:Лобзики и пилы - SGCZ2600DL (788.45 kb)