Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
(4) Let the tool charge initially for at least 10 hours. After the initial charge, your tool should be fully charged in 10 hours from a fully discharged condition. Recharge discharged batteries as soon as possible after use or battery life may be greatly diminished. For longest battery life, do not discharge batteries fully. It is recommended that the batteries be recharged after each use. WARNING: Do not use tool while it is connected to the charger. WARNING: Fire Hazard. When disconnecting the charger from the tool, be sure to unplug the charger from the outlet first, then disconnect the charger from the tool. Important Charging Notes 1. Your tool was sent from the factory in an uncharged condition. Before attempting must be charged for at least 10 hours. B1 3 8 B 3 2. CAUTION: To reduce the risk of damage to the air temperature below 40°F Also, NEVER charge them if the battery temperature Longest life and best performance 6 90547733 LPS7000 Saw 6/11/09 7:21 AM Page 7 temperature of approximately 75°F (24°C). NOTE: The tool will not charge if the tool temperature is below approximately 32°F (0°C) or above 113°F (45°C). 3. While charging, the charger may hum and become warm to touch. This is a normal condition and does not indicate a problem. 4. If the batteries do not charge properly—(1) Check current at receptacle by plugging in a lamp or other appliance. (2) Check to see if receptacle is connected to a light switch which turns power off when you turn out the lights. (3) Move charger and tool to a surrounding air temperature of 40°F (4.5°C) to 105°F (+40.5°C). (4) If the receptacle and temperature are OK, and you do not get proper charging, take or send the tool and charger to your local Black & Decker service center. See Tools Electric in yellow pages. 5. The tool should be recharged when it fails to produce sufficient power on jobs which were easily done previously. Battery life may be greatly diminished if batteries are discharged deeply. DO NOT CONTINUE using product with its batteries in a depleted condition. Recharge discharged batteries promptly. 6. To maximize battery life: a. Do not fully discharge batteries. b. Fully recharge batteries after each use. c. Store tool in a location where the surrounding air temperature is approximately 40°F - 75°F (4.5°C - 24°C). d. Disconnect charger from tool after charge is complete. WARNING: Fire Hazard. When disconnecting the charger from the tool, be sure to unplug the charger from the outlet first, then disconnect the charger cord from the tool. OPERATING INSTRUCTIONS WARNING: Always wear proper eye and respiratory protection while operating this tool. • Use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the work by hand or against your body leaves it unstable and may lead to loss of control. • Place blade and shoe lightly against work to be cut. • Switch on saw motor and allow it to obtain maximum speed before applying pressure. TRIGGER SWITCH (FIGURE C) The tool is equipped with a switch lock-off feature to prevent unintentional operation. • To switch the tool on, press the lock off button (2) from either side, then squeeze the on/off switch (1). • After the tool is running, release the switch lock-off button. The tool will continue to run as long as the trigger is depressed. • To switch the tool off, release the on/off switch. There is no provision for locking the tool on. • This tool is designed with two gripping surfaces for optimal control. Hold saw firmly with one hand (figure C) or both hands (figure D) while cutting. The saw can be used in either of the modes shown in figure E. Whenever possible, the saw shoe (4) must be held firmly against the material being cut. This will prevent the saw from jumping or vibrating and minimize blade breakage. • A light (6) is built-in to the saw above blade holder (5). The light will automatically come on each time the on/off switch is depressed. C E D 1 2 7 90547733 LPS7000 Saw 6/11/09 7:21 AM Page 8 JIG SAW / RECIPROCATING SAW MODES (FIGURES F, F1) The LPS7000 can be used in two different ways: JIG SAW MODE - Blade teeth face forward as shown in figure F. RECIPROCATING MODE - Blade teeth face downward as shown in figure F1. The LPS7000 accepts T-shank blades only. Thin kerf 10tpi or higher blade recommended. BLADE CLAMP RELEASE LEVER (FIGURE G) CAUTION: Burn hazard. Recently used blades may be hot. To install blade into saw: • Push down on the blade clamp release lever ( 5) to its full open position as shown. • Insert blade shank (9) from the front. • Release the blade clamp release lever (5). To remove blade from saw: • Push down on the blade clamp release lever (5) to its full open position. • Remove blade. • Release the blade clamp release lever (5). WOOD CUTTING NOTE: Use “T” shank 10tpi or higher, thin kerf blades. • Before cutting any type of wood, use clamps or another practical way to secure and support the workpiece to a stable platform. Holding the wor...
Эта инструкция также подходит к моделям:Лобзики и пилы - 90547733 (1016.01 kb)