Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
IO.Never use damaged or incorrect blade washers or bolts. The blade washers and bolt were specially designed for your saw, for optimum performance and safety or operation. 4 I 11 iauses and Operator Prevention of Kickback: rickback is a sudden reaction to a pinched, bound or misaligned saw blade, ausing an uncontrolled saw to lift up and out of the workpiece toward the Iperator. Vhen the blade is pinched or bound tightly by the kerf closing down, the blade tails and the motor reaction drives the unit rapidly back toward the operator. f the blade becomes twisted or misaligned in the cut, the teeth at the back tdge of the blade can dig into the top surface of the wood causing the blade D climb out of the kerf and jump back toward operator. rickback is the result of tool misuse and/or incorrect operating procedures Y conditions and can be avoided by taking proper precautions as given below. naintain a firm grip with both hands on the saw and position your body and rm to allow you to resist KICKBACK forces. KICKBACK forces can be ontrolled by the operator, if proper precautions are taken. Vhen blade is binding, or when interrupting a cut for any reason, release he trigger and hold the saw motionless inthe material untilthe blade comes D a complete stop. Never attempt to remove the saw from the work or pull he saw backward while the blade is in motion or KICKBACK may occur. ivestigate and take corrective actions to eliminate the cause of blade binding. Vhen restarting a saw in the workpiece, center the saw blade in th& kerf nd check that saw teeth are not engaged into the material. If saw blade ;binding, it may walk up or KICKBACK from the workpiece as the saw is ?started. ;upport large panels to minimize the risk of blade pinching and KICKBACK. arge panels tend to sag under their own weight. Supports must be placed nder the panel on both sides, near the line of cut and near the edge of the anel as shown in Fig. 1. o minimize the risk of blade pinching and kickback. When cutting operation ?quires the resting of the saw on the work piece, the saw shall be rested n the larger portion and the smaller piece cut off. -------I To avoid kickback do support board Don't support board or panel away or oanel near the cut. from the cut. 1 I I1 Fig. 1 Fig. 2 Do not use dull or damaged blade. Unsharpened or improperly set blades produce narrow kerf causing excessive friction, blade binding and KICKBACK. Blade depth and bevel adjusting locking levers must be tight and secure before making cut. If blade adjustment shifts while cutting, it may cause bindingand KICK BACK. Use extra caution when making a "Pocket Cut" into existing walls or other blindareas. The protruding blade may cut objects that can cause KICKBACK. NEVER place your hand or fingers behind the saw. If kickback occurs, the saw could easily jump backwards over your hand, possibly causing :. severe injury. I Fie.3 12. Adjustments. Before cutting be sure depth and bevel adjustments are tight. 13. Avoid Cutting Nails. Inspect for and remove all nails from lumber before Eutting. 14.When operating the saw, keep the cord away from the cutting area and position it so that it will not be caught on the workpiece during the cutting operation. Operate with proper hand support, proper workpiece support, and supply cord routing away from the work area. A typical illustration of proper hand support, workpiece support, and SUDD~Vcord routinp. WARNING: Fig. 4 Itis important to support the workpiece properly and to hold the saw firmly to prevent loss of control which could cause personal injury. Fig. 4 illustrates typical hand support of the saw. 15 ace the wider portion of the saw base on that part of the workpiece which solidly supported, not on the section that will fall off when the cut is made. E examples, Fig. 5 illustrates the RIGHT way to cut off the end of a board, id Fig. 6 the WRONG way. If the workpiece is short or small, clamp it down. 3N'T TRY TO HOLD SHORT PLACES BY HAND! Fig. 5 Fig. 16 wer attempt to saw with the -cular saw held upside down in a f ;e. This is extremely dangerous and n lead to serious accidents. Fig: 17 !fore setting the tool down after completing a cut, be sure that the lower rlescoping) guard has closed and the blade has come to a complete stop. SYMBOLS The followings show the symbols used for tool. V ................................. A ................................. Hz ................................. kg ................................. h ................................. min ................................. S ................................. 'L ................................. -................................. n, ................................. - 'L ................................. 1_1 *IuI................. volts amperes herts kilograms hours minutes seconds alternating current direct current no load speed alternating or direct current ................. Class II Construction A ................................. splash-proof constructio...