Оценок - 4, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
(2)Avoid storing battery cartridge ina container with other metal objects such as nails, coins, etc. (3)Do not expose battery cartridge to water or rain. 6. Do not store the tool and Battery Cartridge in locations where the tempera- ture may reach or exceed 5OoC (122OF). 7. Do not incinerate the Battery Cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire. SAVE THESE INSTRUCTIONS. Installing or removing the saw blade CAUTION: Always be sure that the tool is switched off and battery removed before installing or removing the blade. To install the blade, loosen the screw on the blade holder. With the blade teeth facing forward, insert the blade into the blade holder as far as it will go. Make sure that the back edge of the blade fits properly in the groove of the roller. Then firmly tighten the screw to secure the blade. CAUTION: Always secure the blade firmly. Insufficient securing of the blade may cause blade break- age or serious injury. Always clean out the blade holder before installing the blade. Chips or foreign matter on the blade holder may cause insufficient securing of the blade. Use a lubricant or cutting oil between the blade and roller when cutting iron or composi- tion board, etc. Failure to do so will shorten the service life of your blade and roller or lead to potentially dangerous blade breakage. Installing the universal shank jig saw blade CAUTION: Always be sure that the tool is switched off and battery removed before installing or removing the blade. If the universal blade clamp is used, you can use blades of other makes which have a universal shank like the one shown in the figure, with a blade width of 6.35 mm (1/4"1. Insert the blade into the blade holder as far as it will go. Make sure that the end of the blade shank reaches the bottom of the inner slit and tighten the bolt securely with the hex wrench. Selecting the cutting action This tool can be operated with an orbital or a straight line cutting action. To change the cutting action, just turn the lever to the desired cutting action position. Refer to the table below to help determine the appro- priate cutting action. Position 1 Cutting action I Applications I For cutting mild steel, stainless steel and plastics. 0 Straight line cutting action For clean cuts in wood and plywood. I I 1 Small orbit cutting action I For cutting mild steel, aluminum and hard wood. I For cutting wood and plywood. 1 II Medium Orbit cutting action For fast cutting in aluminum and mild steel. 1 111 I Large orbit cutting action 1 For fast cutting in wood and plywood. I Switch action CAUTION: Before inserting the battery cartridge into the tool, always check to see that the switch trigger actuates properly and returns to the "OFF" position when released. Pulling the trigger hard when the lock off button is not pressed causes switch damage. - To start the tool, simply push the lock off button then pull the trigger. Release the Lock-off button I Switch trigger I,- // I------- Cutting operation CAUTION: Check carefully that the blade is adequately secured in position before inserting the bat- tery into the tool. Turn the tool on without the blade making any contact. Rest the base flat on the work- I / piece and gently move the tool forward along the previously marked cutting line. Cutting line CAUTION: *Always hold the tool with the base flush with the workpiece. Failure to do so may cause a slanted cutting surface and blade breakage. *Advance the tool very slowly when cutting curves or scrolling. Forcing the tool may cause a slanted cutting surface and blade breakage. Bevelcutting CAUTION: Always remove the battery from the tool before making any adjustments With the base tilted, you can make bevel cuts at any angle between 0" and 45" (left or right). Loosen the bolt on the bottom of the tool. Move the base so that the bolt is positioned in the center of the cross-shaped slot in the base. Cross-shaped slot Tilt the base until the desired bevel angle is obtained. The edge of the motor housing Edge of motor housing indicates the bevel angle by graduations. Then tighten the bolt to secure the base. rl I Flush cutting Loosen the bolt on the bottom of the tool and slide the base all the way back. Then tighten the bolt to secure the base. cutouts Cutouts can be made with either of two methods A or B. A) Boring a starting hole: For internal cut- outs without lead-in cut from an edge, pre-drill a starting hole more than 12 mm (15/32") in diameter. Insert the blade into this hole and hold the tool firmly against the workpiece to start your cut. Starting hole =/ B) Plunge cutting: You need not bore a starting hole or make a lead-in cut if you carefully do as follows. 1) Tilt the tool up on the front edge of the base, with the blade point positioned just above the workpiece surface. 2) Apply firm pressure to the tool so that the front edge of the base will not move when you switch on the tool and gently lower the ...