Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Always position the Saw safely and activate the Throttle Lever (13) repeatedly to make sure all of the air is expended. Refer to FIGURES 2 and 3 below, and the Assembly Drawing on page 8. 1. The Blade Guard (34) may be removed when replacing blades, but it must always be on during operation. Using the Saw without the Blade Guard (34) can result in severe injury. To remove the Blade Guard (34), loosen and remove the two Set Screws (24). When replacing the Blade Guard (34), place it in the slots and tighten the Set Screws (24). 2. To change blades, first remove the Chuck Cover (26) by removing the Screw (38). Swing the Chuck Cover (26) back on its hinge. 3. Loosen the two Set Screws (30) inside, until the blade can be removed. Replace with a new blade and tighten the Set Screws (30). Replace the Chuck Cover (26) and carefully tighten the Screw (38). Do not overtighten the Screw (38) or you may break the plastic Chuck Cover (26). Note: Never use a dull, bent, or cracked blade. Check that the blade and blade guard are tight before each use. FIGURE 2 FIGURE 3 Wrench (31) Set Screw (24) Housing (28) Chuck Cover (26) Blade Blade Blade Guard (34) Screw (38) Set Screw (30) Wrench (36) REV 09f Operation (continued) Using the Saw Note: Always press lightly when cutting. Do not force the Saw. Sudden forceful pressing will shorten the stroke, diminish cutting efficiency, or possibly break the blade. Note: Always operate the Saw with two hands. Hold the top of the Housing (28) with one hand, and hold the lower Housing (28) and Throttle Lever (13) with the other. Failure to use two hands may cause the Saw to vibrate out of your control causing serious injury. Warning! This Saw may be used for cutting through copper, steel, aluminum, and plastics. Do not exceed the maximum 16 gauge thickness when cutting with this Saw. Doing so can cause serious injury and damage to the tool. Warning! Check the saw blade prior to each use. Do not use a cracked, bent, or broken blade. 1. Secure the workpiece in a vise, or clamp it securely to a workbench. 2. Following the directions on page 4, attach the Saw to the air source hose. 3. Push the Throttle Safety forward (see FIGURE 1 on page 5) and pull the Throttle Lever (13). 4. Contact the workpiece allowing the Saw to do the cutting for you. Do not exert pressure on the workpiece. 5. When finished, release the Throttle Lever (13) and disconnect the Saw from the air source. After disconnecting the Saw from the air compressor, there could still be enough air pressure to activate the Saw. Always position the Saw safely and activate the Throttle Lever (13) repeatedly to make sure all of the air is expended. Maintenance 1. After each use, wipe down the Saw with a lint free cloth. 2. Make sure that both the housing that holds the blades and the Air Inlet (9) are free of dirt and debris. 3. Periodically apply a light machine oil to the pivot point of the Throttle Lever (13). See FIGURE 1 on page 5. 4. Before each use, check the blade to make sure it is securely in place. If necessary, tighten the Set Screws (30). 5. Before each use, make sure the Blade Guard (34) is securely in place. Tighten if necessary. REV 09f Parts List Part No. Description Qty Part No. Description Qty 1 Valve Screw 1 26 Chuck Cover 1 2 O-Ring 1 27 Screw 2 3 O-Ring 1 28 Housing 1 4 Air Controller 1 29 Piston Assy 1 5 Valve Spring 1 30 Set Screw 2 6 Valve Stem 1 31 Wrench (2mm) 1 7 O-Ring 1 32 Guide Plate 1 8 Valve Bushing 1 33 Blade Chuck 1 9 Air Inlet 1 34 Blade Guard (long and short) 2 10 Cap Screw 4 36 Wrench (4mm) 1 11 Washer 4 38 Screw 1 12 Lever Pin 1 39 Blade Guide 2 13 Throttle Lever 1 42 Front Bumper 1 15 Valve Case 1 43 Rear Bumper 1 16 Bushing 1 44 Pin 2 17 Cylinder 1 45 Spring 1 18 Valve Sleeve 1 46 Packing 1 19 Actuator Valve 1 47 Packing 1 20 Washer 1 48 Packing 1 21 Cap Screw 3 49 Set Screw 1 22 Gasket 1 50 Rubber Grip 1 23 Valve Block 1 24 Set Screw 2 25 Bushing 2 PLEASE READ THE FOLLOWING CAREFULLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO. NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. REV 09f, 09i Assembly Drawing 39 Note: Only one of the Cap Screws (10) and one of the Washers (11) are shown. 21 21 90 day warranty Harbor Freight Tools Co. makes every effort t...