Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
V~ Volts Alternating Current A Amperes n0 xxxx/min. No Load Revolutions per Minute (RPM) SPECIFIC SAFETY RULES Maintain labels and nameplates on the Tile Saw. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Use the right product for the right job. There are certain applications for which this product was designed. Do not use small equipment, tools, or attach-ments to do the work of larger industrial equipment, tools, or attachments. Do not use this product for a purpose for which it was not intended. This product must continuously run with cold water. Dry running will cause serious damage to the Pump seals. WARNING! Keeps hands and fingers away from cutting area and Saw Blade. Use a “push stick” (not included) when necessary. Check Blade Guard for proper forward/backward movement before each use. Do not operate the Tile Saw if the Blade Guard does not move freely. Make sure the Blade Guard moves freely and does not touch the Saw Blade or any other part of the Saw, in all angles and depths of cut. Do not handle the Power Switch with wet hands. Make sure the Tile Saw is located on a flat, level, sturdy surface capable of supporting the weight of the Saw and work pieces. Always use Diamond Saw Blades with a 7” diameter, 5/8” round arbor hole, and rated at 3550 RPM or greater. Use the Tile Saw only for cutting ceramic tile, quarry tile, marble, terra-cotta, and slate with a maximum thickness of 1” if cutting at a 90 degree angle or 1” if cutting at a 45 degree angle. Do not use the Tile Saw for cutting metals or for cutting curves. This may cause the Saw Blade to break and/or reduce it s service life. Make sure the Saw Blade is wet at all times when cutting. Keep all electrical connections dry and off the ground. REV 12/06 POWER CORD120 VOLT, GROUNDEDELECTRICALOUTLETTILE SAWDRIP LOOPFIGURE CAlways arrange a “drip loop” in the Power Cord connecting the Tile Saw to a 120 volt, grounded, electrical outlet. A drip loop is that part of the Power Cord below the level of the outlet, or the connector if an extension cord is used, to prevent water traveling along the Power Cord and coming in contact with the outlet. If the Power Plug or electrical outlet does get wet, do not unplug the Power Cord. Disconnect the fuse or circuit breaker that supplies power to the tool. Then, unplug and examine for presence of water in the outlet. (See Figure C.) Use cold water only. Never use hot water. Using hot water can damage the Pump seals. Never run the Tile Saw without a water supply. Running the unit without a water supply will cause irreparable damage to the Pump. Make sure the water supply used for the Tile Saw is not dirty, sandy, and does not contain any corrosive chemical products. Make sure to change the water when necessary while in use and rinse out the Tub after every use. Never leave the Tile Saw unattended when it is plugged into an electrical outlet. Turn off the Tile Saw, and unplug it from its electrical outlet. Always keep the water level at the recommended level. Fill the Tank with enough water so that the Pump is about 3/4 completely submerged, but not so much water that the Tank overflows. Avoid splashing water on the Motor, Power Switch, Power Cord, or any other electrical component. Make sure to stand on a dry, insulated surface such as a rubber mat while using the Tile Saw. To avoid accidental injury, always wear heavy duty work gloves when changing the Saw Blade. Before using the Tile Saw, make sure the Saw Blade is properly mounted on the Saw Spindle. Make sure the Saw Blade is balanced, and is not cracked or bent. The Saw Blade will become hot while cutting. Allow the Saw Blade to com- pletely cool before handling. Allow the Saw Blade to spin up to full speed before feeding a workpiece into it. When turning off the Tile Saw, allow the Saw Blade to spin down and stop on its own. Do not press against the Saw Blade to stop it. Do not force the workpiece into the Saw Blade when cutting. Apply moder-ate pressure, allowing the Saw Blade to cut without being forced. Turn off the Tile Saw and allow the Saw Blade to stop on its own if the Saw Blade is to be backed out of an uncompleted cut. Never attempt to remove material stuck in the moving parts of the Tile Saw while it is plugged in and running. When cutting a large workpiece make sure its entire length is properly supported. If necessary, use a roller stand (not included) with larger work pieces. Never stand on the Tile Saw. Serious injury could result if the Tile Saw is tipped or if the rotating Saw Blade is accidently contacted. Industrial applications must follow OSHA requirements. For your safety: In extreme working conditions, sensors in the Tile Saw will automatically switch off the Motor to prevent overheating. In this event, turn the Power Switch to its “OFF” position. Wait five minutes or until the Motor has cooled. Making sure your hands are dry, depress the Circuit Breaker. Then, turn the ...