Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electrician before using it. 8. Protect your extension cords from sharp objects, excessive heat, and damp or wet areas. RECOMMENDED MINIMUM WIRE GAUGE FOR EXTENSION CORDS* (120 VOLT) NAMEPLATE AMPERES (At Full Load) EXTENSION CORD LENGTH 25 Feet 50 Feet 75 Feet 100 Feet 150 Feet 0 – 2.0 18 18 18 18 16 2.1 – 3.4 18 18 18 16 14 3.5 – 5.0 18 18 16 14 12 5.1 – 7.0 18 16 14 12 12 7.1 – 12.0 18 14 12 10 - 12.1 – 16.0 14 12 10 -- 16.1 – 20.0 12 10 --- * Based on limiting the line voltage drop to five volts at 150% of the rated amperes. FIGURE B SYMBOLOGY Double Insulated Canadian Standards Association Underwriters Laboratories, Inc. Volts Alternating Current A Amperes V ~ no No Load Revolutions xxxx/min. FIGURE C Per Minute (RPM) SKU 47003 PAGE 7 SPECIFIC SAFETY RULES 2. 1. Maintain labels and nameplates on the Cut-Off Saw. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. Keep hands and fingers away from cutting area and Cut-Off Wheel. Keep one hand on the Handle and your second hand on the motor housing. If both hands are holding the saw, your hands and fingers cannot be cut by the Cut-Off Wheel. 3. Do not reach under the Base of the Cut-Off Saw. The Swing Guard can not protect you from the Cut-Off Wheel below the Base. 4. Check Swing Guard for proper closing before each use. Do not operate the Saw if the Swing Guard does not move freely and close instantly. Never clamp or tie the Swing Guard into the open position. If the Saw is accidentally dropped, the Swing Guard may be bent. Raise the Swing Guard and make sure it moves freely and does not touch the Cut-Off Wheel or any other part, in all depths of cut. 5. The Swing Guard should be retracted manually only for special cuts such as “Pocket Cuts” and “Compound Cuts.” Raise the Swing Guard only enough to begin the cut. As soon as the Cut-Off Wheel enters the material, the Swing Guard must be released. For all other sawing, the Swing Guard should be allowed to operate automatically. 6. The Saw is not to be used for any cutting operation in the locked down position. The Saw should be in the locked down position only for carrying and storage. 7. Always use Cut-Off Wheels with a 14” Diameter, 1” round arbor hole, and rated at a minimum of 4,000 RPM. Cut-Off Wheels that do not match the mounting hardware of the Saw or that are rated at less than the saw’s maximum RPM may fly off the Saw or may run eccentrically, causing loss of control. 8. Never use damaged or incorrect Cut-Off Wheel washers or bolts. The Cut- Off Wheel’s washers and bolt were specially designed for your Saw, for optimum performance and safety of operation. 9. Do not use the included Cut-Off Wheel to cut aluminum, copper, brass, or other non-ferrous metals. The included Cut-Off Wheel is designed to cut only ferrous (iron containing) metals such as steel alloys and cast iron. If using other Cut-Off Wheels, only use them on materials that the manufacturer recommends. SKU 47003 PAGE 8 10. To avoid accidental injury, always wear heavy duty work gloves and work bib when changing a Cut-Off Wheel. 11. Before using the Cut-Off Saw, make sure the Cut-Off Wheel is properly mounted on the Saw Spindle. Make sure the Cut-Off Wheel is balanced, and is not cracked or bent. 12. The Cut-Off Wheel will become hot while cutting. Allow the Cut-Off Wheel to completely cool before touching. 13. Allow the Cut-Off Wheel to spin up to full speed before feeding it into the workpiece. When turning off the Saw, allow the Cut-Off Wheel to spin down and stop on its own. Do not press against the Cut-Off Wheel to stop it. 14. Do not force the Cut-Off Wheel into the workpiece when cutting. Apply moderate pressure, allowing the Cut-Off Wheel to cut without being forced. 16. Industrial applications must follow OSHA requirements. 17. Always turn off the Cut-Off Saw and unplug the Power Cord from its electrical outlet before changing accessories or performing any inspection, maintenance, or cleaning procedures. 18. Use the right tool or attachment for the right job. Do not attempt to force a small tool or attachment to do the work of a larger industrial tool or attachment. There are certain applications for which this product was designed. It will do the job better and more safely at the rate for which it was intended. Do not modify this product, and do not use this product for a purpose for which it was not intended. 19. Some dust created by power sanding, sawing, grinding, drilling, and other construction activities, contain chemicals known (to the State of California) to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are: lead from lead-based paints, crystalline silica from bricks and cement or other masonry products, arsenic and chromium from chemically treated lumber. Your ri...