Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
The Saw Blade provided is used for cutting wood. Caution:The Safety Cover (88) returns to its original position when the cut is completed and the handle is raised. Never defeat or remove the Safety Cover. 3. Raise the cutting arm by pushing down slightly on the Handle (65), then pulling out the Arm Release Button. See photo on the next page. 4. If making a vertical cut, verify that the Saw Blade is 90 degrees to the Table. Adjust the Saw Blade angle by first loosening the Lever Rod (156) and turn the saw blade left or right so that the bevel scale pointer is set to zero. See photo on the next page. 5. If making miter cuts, raise the Handle (65) fully then loosen the handle Grip (128). Push the handle Grip to adjust the Saw Blade to the desired angle ranging from 0 to 45 degrees, left or right (positive stops at 0 and 45 degrees). When adjusted, tighten the handle Grip (128) again. Make sure that the Vertical Clamp is clear of the cutting path. 6. If making bevel (angle) cuts, raise the Handle (65) fully and loosen the Lever Rod (156) and push down on the Bevel Knob (146) to pass positive stops while moving the Handle (and Saw Blade) to the desired angle (left or right). Use the Bevel Scale as a guide. Tighten Lever Rod again. Caution: Check that the Kerf Boards do not touch the Saw Blade. Adjust if necessary. 7. To slide the cutting arm backward, loosen the knob Screw (105), and slide the arm back. Tighten the knob Screw again. REV 05/04 REV 03/06 SKU 42818 Page 7 Cutting Stock Cutting Stock . Plug the Power Cord into the electrical outlet. 2. With the workpiece secure, turn on the saw by pressing down on the Lock-off Switch Button (64), then squeeze the Switch (70) trigger button. Lock-off Switch Button (64) Switch (70) Trigger Button Handle Grip (128) Handle (65) Bevel Scale Lever Rod (156) Bevel Knob (146) Knob Screw (105) Kerf Boards (121 & 118) Vertical Clamp Arm Release Button Miter Scale Safety Cover (88) Dust Collection Bag Slide Pipe (44) Fence Brush Holder Cap (14) 3. When the Saw Blade comes to full speed, bring the Saw Blade down and begin cutting slowly through the stock without stopping. Warning: Avoid personal injury. Do not disable the Saw Blade Safety Cover (88). Keep fingers and hands away from the moving blade. 4. When the cut is finished, release the Switch (70) trigger button. Wait for the Saw Blade to stop turning before reaching for the cut stock. 5. When you are finished using the saw, press the cutting head down until it locks into position. 6. Unplug the Power Cord from the electrical outlet. 7. Pull out the Lock-off Switch Button (64) and store in a secure place. This prevents unauthorized operation. Slide Cutting To cut larger pieces of stock, follow these steps. 1. Secure the workpiece to the table and fence. 2. Loosen the Knob Screw (105) so that the carriage can slide freely. 3. Raise the cutting arm by pushing down slightly on the Handle, then pulling out the Arm Release Button. SKU 42818 Page 8 4. Pull the carriage all the way forward with the Handle (65). 5. Turn on the saw by pressing down on the Lock-off Switch Button (64), then squeeze the Switch (70) trigger button. 6. When the Saw Blade comes to full speed, bring the Saw Blade down and begin cutting slowly down through the stock until the Saw Blade is completely lowered. Then begin pushing the Handle back toward the fence. Caution: Whenever performing a slide cut, the cut must be done from front to back. Otherwise, the workpiece may be forced out of the clamps and kick back. Kick back of the workpiece could cause injury. 7. When the cut is finished, release the Switch (70) trigger button. Wait for the Saw Blade to stop turning before reaching for the cut stock. Replacing the Saw Blade 1. Unplug the Power Cord Plug from the electrical outlet. 2. Loosen Hex Bolt (A). See illustrations below. 3. Push up on the right side of the Safety Cover (88) releasing it from around the Bolt. 4. Push the Shield assembly out of the way of the Blade Case (31). 5. Press in on the Shaft Lock Button. See illustration on the next page. 6. Place a socket wrench on the Hex Flange Bolt (83) and turn clockwise until the Bolt and Flange can be removed. Blade Case (31) Hex Wrench Hex Bolt (A) Safety Cover (88) Outer Flange (82) Hex Flange Bolt (83) Ring (81) Inner Flange (80) Spindle (77) SKU 42818 Page 9 Socket Wrench Hex Flange Bolt (83) Shaft Lock Button Socket Wrench Hex Flange Bolt (83) Shaft Lock Button . Remove the existing Saw Blade and replace with another 12 inch blade. The new Saw Blade has an arrow on it that must be pointing in the same direction as the large arrow on the outside of the Blade Case (31). Caution: Never use saw blades larger or smaller in diameter than 12 inches, and rated less than 5000 RPM operation. 8. Replace the Outer Flange (82) and Hex Flange Bolt (83). 9. Press in on the Spindle Lock button and retighten the Bolt in a counterclockwise direction with the socket wrench. 10. Replace the Safety Cover to its origina...