Войти:
Оценок - 5, средний балл: 4 ( )

Инструкция по эксплуатации DeWalt, модель D28700

Производитель: DeWalt
Размер: 1.59 mb
Название файла:
Язык инструкции:enesfr
Перейти к скачиванию



Фрагмент инструкции


6 BLOCK FIG. 3 CUT OFF END G FIG. 5 Q F R E For more accurate square cuts, disconnect the power supply, loosen the two fence bolts, push arm down until wheel extends into base. Place a square against the wheel and adjust fence against the square. Securely tighten both fence bolts before use. EQ J FIG. 6 R When making a miter cut, the vise (F) may not clamp securely, depending on the thickness of the workpiece and the miter angle. Other aids (such as spring, bar or C-clamps) will be necessary to secure the workpiece to the fence when making these cuts. TO CHANGE SPACING BETWEEN THE FENCE AND VISE Using the wrench provided, loosen and ( Q) . Adjust the fence (E) to desired locations. Insert both fence bolts in provided locations. Securely tighten use. Depth Stop (Fig. 1) Depth stop is set at the factory for a new 14" (355mm) wheel from cutting into the supporting surface. To allow more depth of cut, use the 8mm hex wrench (G) provided to loosen depth stop bolt (M) and raise bolt to desired height and then jam nut (P) clockwise until seated firmly on the casting. Securely tighten the depth stop bolt before use. CAUTION: When changing to a new wheel, readjust depth stop to original position to prevent cutting into supporting surface. Trigger Switch (Fig. 1) To start the tool, depress the trigger switch (N). To turn the tool off, release the trigger switch. Keep hands and material from wheel until it has coasted to a stop. To prevent unauthorized use of tool, install a standard padlock (not included) into the padlock hole (O) located in the trigger. Removal and Installation of Wheels (Fig. 7, 8) CAUTION: Turn off and unplug the tool before making any adjustments or removing or installing attachments or accessories. Be sure the trigger switch is in the OFF position. Do not make any adjustment while the wheel is in motion. Do not make any adjustment while chop saw is plugged into power supply. 1. Push in wheel lock lever (L) and rotate wheel (J) by hand until wheel lock lever engages slot in inside flange (S) to lock wheel. Loosen the bolt (T) counterclockwise in the center of the abrasive wheel with the 8mm hex wrench (G). Bolt has right-hand thread. 7 English English FIG. 7 L 2. Remove the bolt (T), washer (U), outside flange (V) and old wheel (J). 3. Make sure flange surfaces are clean and flat. Install the new abrasive wheel by reversing the above steps. 4. Do not overtighten bolt. WARNING: Check the work surface that the chop saw rests on when replacing with a new abrasive wheel. It is possible that the wheel may contact ANY ITEMS OR STRUCTURE THAT EXTENDS ABOVE work surface (under the base) when the arm is fully lowered. FIG. 8 J V T S U 8 Mounting CAUTION: Tool must be supported on stable, level, non-skid surface to prevent unexpected movement when operating. PROCEDURE FOR PERMANENT MOUNTING 1. Mark through the holes in the base (D) and drill two 5/16" (7.94mm) diameter, through the mounting surface. 2. Use 1/4" (6.35mm) fasteners to securely mount base mounting surface. CRADLE MOUNTING (FIG. 9) 1. Cut two boards approximately 20" long x 2" high x 4" wide (508 x 50.8 x 101.6mm) . 2. Place the chop saw at desired work location. 3. Place boards tightly along side and nail to work surface. Operation Tipsfor More Accurate Cuts FIG. 9 • Allow the wheel to do the cutting. Excessive force will cause the wheel to glaze reducing cutting efficiency and/or to deflect causing inaccurate cuts. • Properly adjust fence angle. • Make sure material is laying flat across base. • Properly clamp material to avoid movement and vibration. MAINTENANCE Motor Brush Inspection andReplacement (Fig. 10) WARNING: Turn off and unplug the tool. Be sure the trigger switch is in the OFF position. Brushes should be regularly inspected for wear. To inspect brush- .3" (8mm) Y W X Y .3" (8mm) Y W X Y centers or other qualified service organizations, FIG. 10 Z tical replacement parts. NOTE: Unit may be converted to a 3-wire twist lock authorized service center. Lubrication Closed-type, grease-sealed ball bearings are used These bearings have sufficient lubrication packed in them at the factory to last the life of the chop saw. Accessories CAUTION: The use of any other accessory not recommended for use with this tool could be hazardous. Use only high-strength Type 1 organic bonded wheels rated 4100 rpm or higher. Recommended accessories for use with your tool are available at extra cost from your local dealer or authorized service center. If you need assistance in locating your local dealer or authorized service es, unscrew the two end cap screws (W) and remove end cap (X). center contact: DEWALT Industrial Tool Co., 701 East Joppa Road, Remove brush cap (Z). Brushes (Y) should slide freely in brush Baltimore, MD 21286 or call 1-800-4-DEWALT (1-800-433-9258). box. If brushes are worn down to .3" (8mm) as shown in Figure 10 Three Year Limited Warranty they should be replaced. To reinstall, push new brush back into DEWALT will repair, without char...

Эта инструкция также подходит к моделям:
Лобзики и пилы - 621106-00 (1.59 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории