Оценок - 3, средний балл: 4 ( )

Производитель: DeWalt Размер: 1.67 mb Название файла: Язык инструкции:

MINIMUM GAUGE EXTENSION CORD RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES Ampere Rating Volts Total Length of Cord in Feet Gauge of Extension Cord 0-6 240 up to 50 18 AWG 0-6 240 50-100 16 AWG 0-6 240 100-200 16 AWG 0-6 240 200-300 14 AWG 6-10 240 up to 50 18 AWG 6-10 240 50-100 16 AWG 6-10 240 100-200 14 AWG 6-10 240 200-300 12 AWG 10-12 240 up to 50 16 AWG 10-12 240 50-100 16 AWG 10-12 240 100-200 14 AWG 10-12 240 200-300 12 AWG 12-16 12-16 12-16 240 240 240 up to 50 50-100 14 AWG12 AWGGREATER THAN 100 FEET NOT RECOMMENDED Fig. D-1 EXTENSION CORDS Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D-1 shows the correct gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number, the heavier the cord. FUNCTIONAL DESCRIPTION FOREWORD The Delta Unisaw is a 10" left-tilting arbor saw. The Delta Unisaw features set the standard in the table saw industry. A rip fence assembly is not packaged with the product. You MUST install and use a rip fence system for ripping operations. NOTICE: The photo on the manual cover illustrates the current production model. All other illustrations contained in the manual are representative only and may not depict the actual labeling or accessories included. These are intended to illustrate technique only. CARTON CONTENTS UNPACKING AND CLEANING Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone, gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household floor paste wax. Remove the styrofoam packing and any other loose items from the inside of the saw cabinet. To take off the motor cover, use a hex wrench to remove the 1/4 - 20 x 5/8" hex-head screw (B) Fig. 1. Push the motor cover to one side firmly to depress the clips and pull the motor cover off. See the section “MOTOR COVER”. IMPORTANT: The saw is shipped with the saw arbor in the 45° position. NOTE: You must first attach the handwheel to the saw (see the section “BLADE TILTING HANDWHEEL”), then loosen the locking knob on the handwheel. Turn the handwheel until the saw arbor is in the 90° position. Remove the styrofoam packing from inside the saw cabinet. Tighten the locking knob. 7 1 2 2A 4 3 5 6 7 8 9 10 11 12 13 1415 16 17 18 19 20 21 22 23 27 26 25 24 31 30 29 28 35 34 33 32 1 2 2A 4 3 5 6 7 8 9 10 11 12 13 1415 16 17 18 19 20 21 22 23 27 26 25 24 31 30 29 28 35 34 33 32 1. Unisaw 2. Switch (shown with a magnetic starter) 2A. Motor Cover 3. Extension wing (2) 4. Handwheel 5. Blade guard and splitter assembly 6. Upper bracket for splitter 7. Lower bracket for support rod 8. Support rod 9. 7/8" Open end arbor wrench 10. 7/8"x1/2" Closed end arbor wrench 11. Dust chute 12. Miter gauge 13. Cap for miter gauge handle 14. Handle for miter gauge 15. Handwheel lock knob 16. 1/8" Hex wrench 17. 5/64" Hex wrench 18. Hanger for rip fence (2) 19. 7/16-20x1." Hex head screw (6) 20. 5/16-18x1" Hex head screw (4) 21. 5/16-18x1" Flat Head Screw (1) 22. #10x1/2" Hex washer head screw (8) 23. 10-32x1/2" Pan head screw (2) (use w/ LVC starters) 24. 3/4" I.D. Fiber washer (1) 25. 5/8" I.D. Internal tooth washer (1) 26. 7/16" I.D. Flat washer (6) 27. 5/16" I.D. Flat washer (2) 28. 5/16" I.D. Flat washer (1) (use w/ magnetic starters) 29. 5/16" I.D. Lockwasher (3) 30. 1/4" I.D. Fiber washer (1) 31. 13/64" I.D. Flat washer (2) (use w/ LVC starters) 32. 5/8-18 Jam nut (1) 33. 5/16-18 Hex nut (1) (use w/ magnetic starters) 34. 1-3/8" Key (1) 35. Spring clip (2) (use w/ LVC starters) ASSEMBLY For your own safety, do not connect the machine to the power source until the machine is completely assembled and you read and understand the entire instruction manual. ASSEMBLY TOOLS REQUIRED 1/8" Hex wrench (supplied) 5/64" Hex wrench (supplied) 7/8" Open end arbor wrench (supplied) 7/8"x1/2" Closed end arbor wrench (supplied) Various other open-end wrenches or a socket set (not supplied) ASSEMBLY TIME ESTIMATE Assembly for this machine takes approximately two to three hours. 8 BLADE-TILTING HANDWHEEL 1. Install a fiber washer (A) Fig. 1 on the blade-tilting handwheel shaft (B). Install the key (C) into the shaft keyway. 2. Place the handwheel (D) on the shaft (B) Fig. 1. Align the groove (E) in the handwheel with the key (C). 3. Push the handwheel snugly against the fiber washer. Tighten the set screw. 4. Install the lock knob (F) Fig. 2 into the threaded end of the shaft (B). Hand-tighten the lock...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: