Оценок - 0, средний балл: 4
(
)
)
|
Фрагмент инструкции
422-27-655-0068 - 02-14-03 Copyright © 2003 Delta Machinery To learn more about DELTA MACHINERY visit our website at: For Parts, Service, Warranty or other Assistance, please call 1-800-223-7278 (In Canada call 1-800-463-3582). INTRODUCTION The model 36-902, 30" capacity Unifence™ Saw Guide can be assembled to the, Contractors Saw and Unisaw, in addition to other makes of table saws. The 36-902 Unifence Saw Guide includes the fence, carriage assembly, front guide rail, table frame and legs. The accessory 36-893 table for the 36-902 30" Unifence, is not included and must be ordered separately or a similar table must be constructed by following the instructions in this manual. UNPACKING Carefully unpack the Unifence and all loose items from the shipping cartons. 1 32 4 5 6 7 9 10 11 12 13 14 15 8 16 17 Fig. 1 1. Rail 2. Front Table Support Bracket (1) 3. Fence 4. Unifence Body 5. Table leg Support Bracket 6. Table Adapter Plate 7. Table Leg (2) 8. Rear table support bracket 9. 1/4-20x2" Flip stop bolt 10. Flip stop bracket 11. 5/16-18x1" Hex head bolt 12. Flip stop 13. Flip stop knob 14. 1/4-20 Nut 15. Flip stop fiber washer (2) 16. Unifence cursor 17. Angle bracket (5) 14 11 10 15 12 9 13 CONSTRUCTING UNIFENCE TABLE AND SHELF If you purchased the Unifence without the table, a table must be constructed, as follows: 1. A 32" long by 27" wide table is constructed using 3/4" material by following the dimensions shown in Fig. 2. 2. Three undercuts must also be made on the bottom left end of the table. The location and size of the undercuts are shown in detail in Figs. 2 and 3. 3. IMPORTANT: For maximum ease when sliding the fence across the table we suggest that the top of the table be covered with a veneer. 2 Fig. 2 Fig. 3 3 ASSEMBLING TABLE TO SAW 1. If your saw has a right extension wing, front and rear guide rails, they must be removed. 2. Lay the table upside down on the floor or bench, as shown in Fig. 4. 3. Assemble the two table legs (A) Fig. 5 to the bottom of the table using eight #8x7/8" self tapping screws supplied. NOTE: Refer to Fig. 2 for the hole location for the 36-902 30" Unifence. Fig. 4 A Fig. 5 4. Insert foot adapter (T) Fig. 6, into the bottom of each leg (A). Assemble the 3/8" jam nut (V) approximately 3/4 of the way onto leveling screw (W). Thread the leveling screw (W) into foot adapter. Fig. 7 illustrates the foot leveling assembly on the table leg. Assemble the remaining foot assembly to the other table leg in the same manner. NOTE: Height adjustments can be made later. 4. Assemble table leg support bracket (B) Fig. 8, to the table legs (A) using two U-clamps (C), flat washers, and hex nuts. Fig. 6 B A C Fig. 7 Fig. 8 4 5. Fasten the front table support (F) Fig. 9, to the bottom of the table as shown using two #8x7/8" long wood screws (H) and (I) supplied. NOTE: The vertical flange, on the table board support (F), should be flush with the front edge of the table board. NOTE: The slots closer to the angles in the support (F) should be against the table. NOTE: Screws (H) and (I) Fig. 9 should not be completely tightened to the table board at this time. Screw (I) will have to be removed later. NOTE: Make certain the end of the table support does not extend out past the table. CAUTION: DO NOT OVER-TIGHTEN MOUNTING SCREWS. Over-tightening screws in particle board may cause them to strip. FOR UNISAWS ONLY 6. Fasten the rear table support (A) Fig. 10, to the saw table. Insert a 3/8-24x5/8" hex head screw (B), through hole in rear support and thread screw into tapped hole in table. Repeat this process for the remaining hole. Tighten screws securely. NOTE: FLAT EDGE (D) Fig. 10 AND FIG. 10A, OF REAR TABLE SUPPORT WILL FACE UPWARD. FOR 10" CONTRACTORS SAWS ONLY 6. Fasten the rear table support (A) Fig. 10, to the saw table. Insert a 3/8-16x1" hex head screw (B), through hole in rear support and table, place a 3/8 washer onto the screw and thread a 3/8-16 hex nut onto screw and tighten securely. Repeat this process for the remaining hole. NOTE: FLAT EDGE (D) Fig. 10 AND FIG. 10A, OF REAR TABLE SUPPORT WILL FACE UPWARD. 7. If your saw is equipped with a cast iron wing as shown at (I) Fig. 10. which has a smooth surface, hole (C) Fig. 10 is not used, proceed to step 8. If your saw has a sheet metal wing as shown at (W) Fig. 10A, with a ribbed surface, the rear table support will be fastened through hole (C) Fig. 10A as follows. Insert a 3/8-16x1" hex head screw through hole (C) and the sheet metal extension wing, place a 3/8" washer on the screw, thread a 3/8-16 hex nut on screw, and tighten securely. FOR ALL TABLE SAWS 8. Assemble the three brackets (J) to the table adapter plate (K) using the three 1/4-20x3/4" carriage bolts, nuts and washers, as shown in Fig. 11. NOTE: The long leg of the brackets (J) should be against the adapter plate (K) as shown. Do not completely tighten brackets (J) to adapter plate (K) at this time. F H I Fig. 9 AB B C D I Fig. 10 W C D B B A Fig. 1...