Оценок - 5, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Place the dust port in the opening at the base of the saw. 2. Using a Phillips head screwdriver and an 8mm wrench, secure the dust port to the saw with the Phillips head screws, the hex nuts, the exterior tooth washers, and the toggle tabs (Figure 16). Figure 16. Dust port installation. Components and Hardware Needed: Qty Handwheels........................................................2 Threaded Chrome Handles 3.8"-16 x 1.2" ............2 Star Knobs 3.8"-16 ..............................................2 Tools Needed: 14mm Wrench or Socket....................................1 To install the handwheels: 1. Thread a chrome handle into each hand- wheel. 2. Using a 14mm wrench, final tighten the handles on each handwheel. 3. Slide each handwheel over the threaded shafts that protrude from the side and front of the saw (Figure 17). Note—Align the keyway on the back of each handwheel with the roll pin on the threaded shafts. Handwheels Figure 17. Installed handwheel. 4. Secure the handwheels to the threaded shaft with the star knobs (Figure 17). 5. Using the blade tilt handwheel, adjust the trunnion assembly until the bevel scale reads 90°. -20- G0444/G0444Z 10" Table Saw Motor Components and Hardware Needed: Qty Motor ..................................................................1 Motor Plate ........................................................1 Motor Bracket ....................................................1 Motor Bracket Shaft............................................1 V-Belt Plate ........................................................1 V-Belt Guard ......................................................1 Hex Bolts 5.16"-18 x 1 ........................................4 Hex Nuts 5.16"-18 ................................................4 Flat Washers 5.16" ..............................................8 Lock Washers 5.16" ............................................4 Carriage Bolt 1.4"-20 x 13.4" ................................1 Brass Wing Nut 1.4"-20 ......................................1 Speed Nut 1.4" ....................................................1 Tools Needed: 12mm Wrench or Socket....................................1 10mm Wrench or Socket....................................1 4mm Allen Wrench ............................................1 To install the motor: 1. Using a 12mm wrench, loosely secure the motor to the motor plate with the hex bolts, the lock washers, the flat washers, and the hex nuts (Figure 18). Motor Plate Figure 18. Installed motor plate. 2. Slide the carriage bolt through the hole in the V-belt plate and slide the speed nut over the carriage bolt end. 3. Slide the v-belt plate between the motor and the motor plate and over the hex bolts (Figure 19). V-Belt Plate Figure 19. Installed V-belt plate. 4. Finger tighten the fasteners that secure the motor to the motor plate. 5. Secure the motor plate to the motor bracket with the motor bracket shaft (Figure 20). Note—The hex bolt on the motor bracket must align with the groove on the motor bracket shaft. Motor Bracket Motor Bracket Shaft Figure 20. Installed motor bracket. G0444/G0444Z 10" Table Saw -21 6. Tighten the hex nut on the motor bracket to secure the motor bracket shaft into place. 7. Slide the motor assembly onto the two shafts protruding from the back of the saw (Figure 21). Setscrews Shafts Figure 21. Installed motor assembly. 8. Using a 4mm Allen wrench, tighten the two setscrews (Figure 21) in the motor bracket to secure the motor assembly to the shafts. 9. Raise the motor assembly and slip the V-belt over the motor and arbor pulleys (Figure 22). Lower the motor assembly to tension the V- belt. 10. Place a straightedge across the arbor pulley and the motor pulley. The straightedge should align across the face of both pulleys (Figure 23). ! Figure 23. V-belt alignment. — If the pulleys are not aligned, loosen the bolts tightened in step 4 and reposition the motor. 11. Secure the V-belt guard to the V-belt plate with the brass wing nut (Figure 24). ! Figure 22. V-belt installation. Figure 24. Installed pulley cover. -22- G0444/G0444Z 10" Table Saw Extension Wings Components and Hardware Needed: Qty Extension Wings ................................................2 Hex Bolts 7.16"-14 x 11.4" ......................................6 Lock Washers 7.16" ..............................................6 Flat Washers 7.16"................................................6 Tools Needed: 17mm Wrench or Socket....................................1 Straightedge ......................................................1 To install the extension wings: 1. Align the extension wing holes with the holes on the cast iron table edges. 2. Using a 17mm wrench, secure the extension wings to the cast iron table with the hex bolts, the lock washers, and the flat washers. 3. Lay a straightedge across the extension wings and cast iron table surface. — If the straightedge lays flat across all three surfaces, then skip ahead to the next sub-se...
Эта инструкция также подходит к моделям:Лобзики и пилы - G0444Z (4.73 mb)