Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
English HUSQVARNA CONSTRUCTION PRODUCTS Compliance with EU directives Husqvarna Construction Products Sweden AB, Box 2098, SE-550 02 Jonkoping, Sweden, tel: +46 (0)36-570 60 00, hereby certifies that its FS800 E/EM floor saw, having serial numbers 01001 onwards, is manufactured in compliance with the Council's machinery directive 98/37/EG, low-voltage directive 73/23/EEG and EMC directive 89/336/EEG, including amendments, and that the following standards were used for guidance: EN 55 014-1, EN 55 014-2, EN 61 000-3-2, EN 50 144-1. (Stamp comment Placerad bild em9ash 12.12.2006 15:43:24 blank) Jonkoping 1 February 2001 Christer Carlberg CEO 2 Contents General instructions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Description and purpose. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 Safety precautions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Rating plates, warning signs and their meanings. . . . . . . . . . .5 Preparations before starting. . . . . . . . . . . . . . . . . . . . . . . . . . . .5 Starting and operating. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6 Maintenance. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7 Fitting and replacing diamond blades. . . . . . . . . . . . . . . . . . . . .8 Lifting and transport. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Troubleshooting. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9 Technical specifications. Noise and vibration measurement. 10 Parts list. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .Appendix 1, 11 Exploded diagram. . . . . . . . . . . . . . . . . . . . . . . . .Appendix 2, 13 General instructions _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ The FS800 E/EM floor saw is a professional machine designed for cutting reinforced concrete, asphalt and stone. This machine may only be used by those who have carefully read this instruction manual and follow its instructions. If you are unsure about any point please consult the supplier before starting to use the machine. You must not modify the saw in any way without obtaining written approval from Husqvarna Construction Products Sweden AB. Modifications that are not approved could lead to serious or fatal injury to yourself or others. Husqvarna Construction Products Sweden AB does not accept any liability (Text Box comment not comply with these instructions.) if the machine is used in any way or for any purpose that does 1. Description and purpose The FS800 E/EM electric floor saw is designed for cutting reinforced concrete, asphalt and other stone material in the building industry. The saw has a full-width blade shaft, as shown in figure 1.1.2. This permits a diamond blade to be fitted on either the right of left side of the machine to allow cutting into corners from either side. The blade guard can be divided as shown in figure 1.1.5. The floor saw is equipped with a water-cooling system, as shown in figure 1.2.2 to ensure effective cooling of the diamond blade and prevent dust formation. The FS800 E/EM floor saw has the following controls: • Height adjustment wheel as shown in figure 1.1.1. • Blade shaft as shown in figure 1.1.2. • Alignment guide for cutting a straight line as shown in figure 1.1.4. • Adjuster screw for the above, as shown in figure 1.1.3. • Blade guard as shown in figure 1.1.5. • Control panel with switch, phase inverter and emergency stop as shown in figure 1.1.8. • Power socket as shown in figure 1.2.1. • Water-cooling nozzle as shown in figure 1.2.2. • Guard for exposed drive shaft as shown in figure 1.2.3. • Parking brake as shown in 1.2.4. Figure 1.1 1 8 6 3 4 5 7 2 1.1.1. Height adjustment wheel 1.1.2. Pulley shaft 1.1.3. Adjuster screw for alignment guide 1.1.4. Alignment guide 1.1.5. Two-piece blade guard 1.1.6. Lifting handle for blade guard 1.1.7. Guide handle 1.1.8. Control panel with switch, phase inverter and emergency stop Figure 1.2 4 2 1 3 1.2.1. Power socket 1.2.2. Water-cooling coupling 1.2.3. Guard for exposed pulley shaft 1.2.4. Parking brake 4 _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ ___ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ _ 2. Safety precautions You must follow the safety precautions before starting the machine. If the user does not follow these precautions then neither Husqvarna Construction Products Sweden AB nor its representative can accept any liability, whether direct or indirect. The machine must not be used by any authorised person unless supervi...
Эта инструкция также подходит к моделям:Лобзики и пилы - FS 800 EM (492.35 kb)