Войти:
Оценок - 1, средний балл: 4 ( )

Инструкция по эксплуатации Bosch, модель 3915

Производитель: Bosch
Размер: 2.39 mb
Название файла: fcd60140-d93c-b714-6972-f0c1ef6554c1.pdf
Язык инструкции:enesfr
Перейти к скачиванию



Фрагмент инструкции


NOTE: The board does not slide completely through the opening. The saw must be placed over two (2) boards, one on each side. Figure 16. Portable Mounting Using Clamps 051015 2025303540 45 50 50 45 40 35 30 BOSCH 2x4 Nailed to Workbench 051015 2025303540 4550 50 45 40 35 30 BOSCH Clamping Areas Clamping Area Figure 17. Portable Mounting Using 2x4’s 18. Position your body and hands properly to make cutting easier and safer. Observe the following instructions (Figure 18). Never place hands near cutting area. Keep hands outside the “No Hands” zone. The “No Hands Zone” is defined as the area between marked lines on the left and right side of the Base, including the entire Table and portions of the Fence within these marked lines. This zone is labeled by “No Hands” symbols placed just inside the marked lines on the Base. Hold workpiece firmly to the fence to prevent movement. Keep hands in position until trigger has been released and blade has stopped completely. Never place hands on slide rails. Figure 18. Hand Positions Keep feet firmly on the floor and maintain proper balance. Follow the miter arm when mitering left or right. Stand slightly to the side of the saw blade. Before making any cut, with the power off, lower the blade to preview the blade path. The lower guard may not automatically open under certain cutting conditions. If this occurs: Typically this may occur when trying to cut workpieces that are near the maximum cutting height capacity. Under these conditions, the workpiece can stop the lower guard movement before the downward motion of the arm could pre-open the lower guard. If this occurs: Workpiece must be securely clamped. This frees a hand to raise the guard by the lip just enough to clear the workpiece (Figure 19). Start the saw and begin your cut. Once you have cleared the position where the lower guard may bind, release the guard and it will continue to operate automatically as you cut. Figure 19. Raising Lower Guard Open Workpiece Lip Lower Guard BOSCH 0 5 10 15 20 25 30 35 40 45 50 5045 40 35 30 BOSCH 0 5 10 15 20 25 30 354045 50 50 45 40 35 30 BOSCH 0 5 10 15 20 25 30 35 40 45 50 50 45 4035 30 BOSCH 0 5 10 15 20 25 30 354045 50 50 4540 35 30 BOSCH Correct Incorrect Use 19. Basic Saw Operations Body and Hand Position ! WARNING ! WARNING 20. Long workpieces have a tendency to tip over unless clamped down and properly supported from underneath. Clamps Workpiece Clamp - This clamp easily secures a workpiece in any of four (4) clamp holes behind the fence (Figure 20). — Insert clamp post into clamp hole. — Loosen wing nut and adjust arm to proper height, and securely tighten wing nut. — Rotate screw knob of the clamp clockwise to tighten, counter-clockwise to loosen. — Move the head assembly to check clearance with clamp. There may be extreme compound cuts where clamp cannot be used. Support workpiece with hand outside No Hands Zone. Do not try to cut short pieces that cannot be clamped and cause your hand to be in the No Hands Zone. Figure 20. Workpiece Clamp Conventional Clamps and other hold down devices can be used to hold the workpiece firmly against the table and the fence. Long Workpiece Support Blocks - Long pieces need extra support. The base height (3-3/4") is designed to match the standard lumber of two 2x’s and one 1x. Boards of these thicknesses can be used to create auxiliary support extensions for long workpieces (Figure 21). Figure 21. Block Support Extension Wing and Stock Stop - This attachment (accessory #BA162) allows extra support for the longer workpieces. Refer to the accessory instruction sheet for details (Figure 22). See page 34 for a complete accessory list. Figure 22. Extension Wing and Stock Stop 0 5 10 15 20 25 30 35 40 45 50 50 45 40 35 30 BOSCH Extension Wing and Stock Stop Extension Wing and Stock Stop 50 45 4035 30 25 20 15 10 5 0 25 30 35 40 45 50 Two 2x’s and One 1x’s BOSCH 0 5 10 15 20 25 30 35 40 45 50 50 45 40 35 30 BOSCH Clamp Holes Clamp Holes Clamp Post Screw Rod Workpiece Clamp Basic Saw Operations Workpiece Support ! WARNING ! WARNING Basic Saw Operations Auxiliary Fence - Certain types of molding need a fence face extension because of the size and position of the workpiece. Holes are provided in the fence to attach an auxiliary fence. The auxiliary fence is used with the saw in the 0° bevel position only. 1. Place a piece of wood against the miter saw fence (Figure 23). (Wood can have a maximum height of 3-1/4". Check that head assembly does not interfere with auxiliary fence.) 2. Mark the locations of the support holes on the wood from the back side of the fence. 3. Drill and countersink the holes on the front of the support board. 4. Attach the auxiliary fence using three (3) 1/4" flat head machine screws. Make a full depth cut to create the blade slot. Check for interference between the auxiliary fence and the lower blade guard. Make adjustments as necessary. WARNING ! Check for interference from any components. 05101520253035404550...


Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории