Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
To make sharp corners, cut up to the corner, then back up slightly before rounding the corner. After the opening is complete, go back to each corner and cut it from the opposite direction to square it off. Do not try to plunge cut into hard materials such as steel. CIRCLE AND PARALLEL CUTTING GUIDE This accessory is available at an extra cost. It is used for fast and accurate straight and circle cutting (Fig. 6). ATTACHING GUIDE 1. Insert bar of guide through lock knob clamp, then through the slots provided in foot, from either side of foot with the edge guide facing down (Fig. 6). FIG. 6 LOCK KNOB CLAMP GUIDE PIN BAR EDGE GUIDE DOWN FIG. 7 GUIDE PIN GUIDE PIN HOLE WEDGE EDGE GUIDE UP 5. Measure the distance from the selected hole to the blade to be equal to the circle radius. 6. Move switch lock to the unlock position, hold the saw firmly, squeeze trigger and slowly push the saw forward. To make a hole, cut from inside the circle; To make wheels or discs, cut from the outside. Cutting Tip: Cut slowly so the blade will stay straight in the cut. Place small wedges in the cut as shown in Fig. 7, to keep the inner circle from spreading when near the end of the cut. -10 BM 2610925943 6-05 6/10/05 10:25 AM Page 11 RELEASING AND INSERTING BATTERY PACK Release battery pack from tool by pressing pack. To insert battery, align battery and slide on both sides of the battery release tabs and battery pack into tool until it locks into pull downwards. Before inserting battery position. Do not force. pack, remove protective cap from battery IMPORTANT CHARGING NOTES 1. The battery pack accepts only about 80% of its maximum capacity with its first few charge cycles. However, after the first few charge cycles, the battery will charge to full capacity. 2. The charger was designed to fast charge the battery only when the battery temperature is between 40°F (4°C) and 105°F (41°C). 3. A substantial drop in operating time per charge may mean that the battery pack is nearing the end of its life and should be replaced. 4. If you anticipate long periods (i.e. a month or more) of non-use of your tool, it is best to run your tool down until it is fully discharged before storing your battery pack. After a long period of storage, the capacity at first recharge will be lower. Normal capacity will be restored in two or three charge/discharge cycles. Remember to unplug charger during storage period. 5. If battery does not charge properly: a. Check for voltage at outlet by plugging in some other electrical device. b. Check to see if outlet is connected to a light switch which turns power “off” when lights are turned off. c. Check battery pack terminals for dirt. Clean with cotton swab and alcohol if necessary. d. If you still do not get proper charging, take or send tool, battery pack and charger to your local Bosch Service Center. See “Tools, Electric” in the Yellow Pages for names and addresses. Note: Use of charger’s or battery packs not sold by Bosch will void the warranty. -11 BM 2610925943 6-05 6/10/05 10:25 AM Page 12 CHARGING BATTERY PACK (30 MINUTE SINGLE BAY-BC130) INDICATORS, SYMBOLS AND MEANING If the indicator lights are “OFF”, the charger is not receiving power from power supply outlet. If the green indicator light is “ON”, the charger is plugged in but the battery pack is not inserted, or the battery pack is fully charged and is being trickle charged. If the green indicator light is “BLINKING”, the battery pack is being fast-charged. Fast- charging will automatically stop when the battery pack is fully charged. If the red indicator light is “ON”, the battery pack is too hot or cold for fast-charging. The charger will switch to trickle charge, until a suitable temperature is reached, at which time the charger will switch automatically to fast-charging. If the red indicator light is “BLINKING”, the battery pack cannot accept a charge or the contacts of the charger or battery pack are contaminated. Clean the contacts of the charger or battery pack only as directed in these operating instructions or those supplied with your tool or battery pack. Plug charger cord into your standard power outlet. Before inserting battery pack, remove protective cap, then insert battery pack into charger (Fig. 8). The charger’s green indicator light will begin to “BLINK”. This indicates that the battery is receiving a fast charge. Fast-charging will automatically stop when the battery pack is fully charged. When the indicator light stops “BLINKING” (and becomes a steady green light) fast charging is complete. The battery pack may be used even though the light may still be blinking. The light may require more time to stop blinking depending on temperature. When you begin the charging process of the battery pack, a steady red light could also mean the battery pack is too hot or too cold. The purpose of the green light is to indicate that the battery pack is fast-charging. It does not indicate the exact point of full charge. The light will stop blink...
Эта инструкция также подходит к моделям:Лобзики и пилы - 52324 (2.32 mb)
Лобзики и пилы - 52318 (2.32 mb)