Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
General safety instructions 4 This product is warranted for a 2-year period for home Additional safety rules for band saws Unpacking Know your product Components Assembly 5 6 6 8 8 domestic use from the date of the original purchase. If found to be defective in materials or workmanship, the tool or the offending faulty component will be repaired or replaced free of charge with another of the same item. A small freight charge may apply. Proof of purchase is essential. We reserve the right to reject any claim where Mounting to a workbench 9 the purchase cannot be verified. Lower blade guide adjustment 10 This warranty does not include damage or defects to the Housing doors 11 tool caused by or resulting from abuse, accidents, Adjusting the rip fence 11 alterations or commercial or business use. It also does not Adjusting the mitre gauge Adjusting the bevel angle 11 11 cover any bonus items or included accessories. Only the power tool is covered under this warranty. Adjusting the saw blade tension Adjusting the blade tracking Dust collector connection 12 12 12 With continuing product development, changes may have occurred which render the product received slightly different to that shown in this instruction manual. Turning on and off 13 Please ensure that you store your receipt in a safe place. Turning the laser on and off Turning the LED lights on and off Removing and installing band saw blades Operation Using the REDEYE® laser line generator Power cord maintenance Cleaning 13 13 13 14 14 15 15 Conditions apply to the above warranty. For full details of the warranty terms and conditions please refer to our website – For prompt service we suggest you log your service request online -should you not have access to the internet, please contact our service department on 1300 880 001 (Australia) or 0800 445 721 (New Zealand). General inspection 15 Troubleshooting 16 2 Introduction Your new GMC power tool will more than satisfy your expectations. It has been manufactured under stringent GMC Quality Standards to meet superior performance criteria. You will find your new tool easy and safe to operate, and, with proper care, it will give you many years of dependable service. CAUTION. Carefully read through this entire Instruction Manual before using your new GMC Power Tool. Take special care to heed the Cautions and Warnings. Your GMC power tool has many features that will make your job faster and easier. Safety, performance, and dependability have been given top priority in the development of this tool, making it easy to maintain and operate. Environmental protection Recycle unwanted materials instead of disposing of them as waste. All tools, hoses and packaging should be sorted, taken to the local recycling centre and disposed of in an environmentally safe way. Warnings. It may be more difficult to see the laser line in conditions of bright sunshine and on certain surfaces. Description of symbols The rating plate on your tool may show symbols. These represent important information about the product or instructions on its use. Wear hearing protection. Wear eye protection. Wear breathing protection. Conforms to relevant standards for electromagnetic compatibility. Specifications Voltage: 230–240V ~ 50Hz Input Power: 300W No Load Speed: 1400 RPM Blade Speed: 680 metres/min Throat Depth: 230mm Table Size: 305mm x 300mm Cutting Capacity: 90mm Blade Length: 1511mm Product Weight: 16.5kg Laser Class: 2 Laser Wavelength: 650nm Laser Output Power: .1Mw 3 Safety rules for laser lights General safety instructions The laser light/laser radiation used in the GMC REDEYE® system is Class 2 with maximum 1mW and 650nm wavelengths. These lasers do not normally present an optical hazard, although staring at the beam may cause flash blindness. WARNING. Do not stare directly at the laser beam. A hazard may exist if you deliberately stare into the beam, please observe all safety rules as follows; • The laser shall be used and maintained in accordance with the manufacturer’s instructions. • Never aim the beam at any person or an object other than the work piece. LASER LIGHT LASER RADIATION Do not stare into beam. Class 2 laser product. Wave length: 650nmOutput power: .1mW AS/NZS 2211.1:2004 • The laser beam shall not be deliberately aimed at personnel and shall be prevented from being directed towards the eye of a person for longer than 0.25s. • Always ensure the laser beam is aimed at a sturdy work piece without reflective surfaces. i.e. wood or rough coated surfaces are acceptable. Bright shiny reflective sheet steel or the like is not suitable for laser use as the reflective surface could direct the beam back at the operator. • Do not change the laser light assembly with a different type. Repairs must only be carried out by the laser manufacturer or an authorised agent. CAUTION. Use of controls or adjustments or performance of procedures other than those specified herein may result in hazardous r...