Plug is configured for the appropriate electrical supply. • The unit is intended for indoor use only. • Never push objects into this product through cabinet slots. Do not spill liquid of any kind on this product. • Do not operate if the product has been exposed to rain or water. SERVICE Do not attempt to service or repair the CombPRO 1000 yourself. Unplug the unit and contact an authorized GBC service representative for exchange or repair. CLEANING CAUTION: Unplug this product before cleaning. Wipe exterior only with a damp cloth. Do not use detergents or solvents. The following notes apply only to the units rated 230V 50Hz. MAIN CORDSET SELECTION (FOR 230VAC MACHINES ONLY) When choosing a detachable line cord for use with the CombPRO 1000, always observe the following: The cordset consists of three components; the attachment plug, cordage and appliance inlet. Each of these components must meet European regulatory approvals for safety. The following minimum electrical ratings for the specific cordset are published for safety purposes. DO NOT USE CORDSETS THAT DO NOT MEET THE FOLLOWING MINIMUM ELECTRICAL REQUIREMENTS. PLUG: 3A, 250 volts, 50/60 Hz, Class 1,3 conductor, European safety agency approved. CORDAGE: Type H05W-F3G0.75, Harmonized (< HAR >). The" < >' symbols indicate cordage approved to appropriate European standard (NOTE: “HAR" may be substituted by the approval mark of the European safety agency which approved the cordage. An example would be “ Think you tor purchasing the GBC CombPRO 1000. This system features our new exclusive Radial Bind design. This design enables you to assemble your document as you punch, making It easier to load paper onto the binding element than previous systems! The CombPR01000 advanced punching technology also makes It easier to punch more paper at once while providing greater reliability. A. GETTING STARTED 1. firmly push the female end of the power cord into the power cord receptacle (A) located on the back of the machine. A CAUTION: Make sort this step Is complete prior to plugging the male end of the power cord into a power receptacle. 2. Plug the male end of the power cord into an appropriate power receptacle. 3. Firmly attach foot pedal cord to receptacle located on back of machine. B. DETERMINE SHEET WIDTH 1. Set Edge Guide (B) to paper size you wish to bind (11“. 8-1/2" letter size, 11-1/4' oversized cover, A4 ring, A5, Japan A4) (see figure 1). When using oversized covers, set the Edge Guide on Covers, punch all of the covers for your job and set aside. Move the Edge Guide back to the 11* setting to punch your contents then bind. 2. Raise lid on cover (D), and pull up appropriate selector pins to disengage punch pins that may nick the edge of your sheet To determine which pins should be pulled up follow the punch steps indicated in section *0' using blank test paper. C. DETERMINE PLASTIC COMB SIZE 1. Slide the Binder Sizer open (C) (see figure 1). 2. Place document including covers behind Binder Sizer. 3. Release the Binder Sizer and select the comb binding element that corresponds with the size shown by guide. Only comb sizes up to 1’ (25 mm) are shown. Your CombPRO can bind documents up to 425 sheets, or 2" (50 mm) comb size. For best results, always use GBC brand covers with GBC color-coordinated binding combs. 4. Adjust the Punch Back Guide (C1) to the setting that corresponds with the plastic comb size to be used. D. PUNCHING PAPER (see figure 2) 1. Lift the Wire Paper Support (D) into place (optional). 2. Align sheets or covers and insert edge to be bound into punch throat (01). 3. Jog the sheets until they are flush against the edge guide and the bottom of the punch throat. Allow the paper to rest against the Wire Paper Support, or, you may prefer to hold the sheets in place with one hand. 4. To punch, press the PUNCH æ button (02) or depress the foot pedal (03). The CombPRO 1000 punches up to 21 sheets of 20 lbV80 gram paper at once. Punch only TWO clear covers at a time to prevent jams and excessive wear. 5. If you try to punch too many sheets GBC's patented ‘Jam Stopper” safeguard feature will automatically stop and reverse the punch die. At this time the yellow LED indicator will temporarily flash. Remove the paper from the punch thr...
)
