Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
• If the laminated item is wavy, the TEMPERATURE is too hot. Verify temperature selector is set at the appropriate temperature. • Always allow sufficient time for the laminator to adjust to changes in temperature setting. The inside of the laminator will glow green when the laminator has reached operating temperature. Position the document to be laminated into a GBC laminating pouch, so that the document is aligned to the folded sealed edge and the right and left borders are equal and insert the pouch into the carrier (fig. 3). Insert the carrier straight into the machine, leading with the folded edge (fig. 4). The carrier will automatically exit the rear of the machine. After the carrier has stopped moving, immediately place it on a flat surface to cool for one minute before handling (fig. 5). If you have finished laminating, push the switch to turn "OFF" the machine. 1 4 CARRIER 2 3 5 CARRIER 6 Copy Paper Setting Glossy Paper Setting Photo Paper Setting 2 - 4 4 - 6 7 - 8 4 - 6 6 - 8 9 - 10 3 mil. 5 mil. The inside of the laminator will glow green. Use and laminate your GBC cold pouch. (Pressure sensitive—non-thermal laminating pouch) Connect power cord to appropriate power source. Rotate the temperature dial to the "cold" position (fig. 2). Push the power button to turn the power "ON" (fig. 2). Operation, cold lamination 1 2 3 4 5 Anti-jam feature: Important Information How to use the release lever. 1 2 If carrier jams or is fed improperly, turn off the laminator immediately. Press the release lever down to release the motor from the rollers (fig. 6). Helpful lamination hints 1 Temperature setting Guidelines: When laminating thin paper with light ink coverage, set the temperature dial at the low end of the range. Thick paper and heavy ink coverage require higher settings. Temperature settings will vary due to the finish, chemistry and heat absorption properties of the material being laminated. 2 Before laminating important or unique documents always run a test pouch through the laminator using a similar type document. Warranties Operation of this machine is guaranteed for two years from date of purchase, subject to normal use. Within the guarantee period, GBC will at its own discretion either repair or replace the defective machine free of charge. Defects due to misuse or use for inappropriate purposes are not covered under the guarantee. Proof of date of purchase will be 3 4 3 4 Pull your carrier out of the laminator while pressing the release lever down (fig. 7). Continue laminating. As soon as the lamination is completed, remove from the rear of the machine and place on a cool flat surface for cooling to prevent the pouch from curling. Your Laminator is equipped with an automatic shut-off function. If the machine remains idle for one hour, the heater function will automatically shut down. To reset the machine for operation, push the power button off first and back on again. required. Repairs or alterations made by persons not authorised by GBC will invalidate the guarantee. It is our aim to ensure that our products perform to the specifications stated. This guarantee does not affect the legal rights which consumers have under applicable national legislation governing the sale of goods. 7 Specifications Electrical Machine Dimensions Machine Weight Maximum Pouch Width Maximum Pouch Thickness Maximum Thru-put Thickness Warm-Up Time (2 x 75 mic) GBC HeatSeal H210 120V / 60Hz / Amps / W 400 x 173 x 117.5mm (15.75” x 6.75” x 4.62”) 2.7 kg (6 lbs.) 241mm (9.5”) 5mil. 1.0 mm (.040”) 5 minutes GBC HeatSeal H310 120V / 60Hz / Amps / W 476 x 173 x 117.5mm (18.75” x 6.75” x 4.62”) 3.75 kg (8.25 lbs.) 318mm (12.5”) 5mil. 1.0 mm (.040”) 6 minutes Register this product online at (Text Box comment Office Zone) (Text Box comment 800.543.5454) (Text Box comment 45 ...
Эта инструкция также подходит к моделям:Ламинаторы - H210 (107.39 kb)