Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Power Light 2. Foam Board/Pouch Selector 3. On/Off Switch 4. Ready Light 5. Temperature Control 6. Loading Area Safety Instructions 1. Read all instructions before use. Save these instructions for later use. 2. Follow all warnings and instructions marked on the product. 3. Use the Fellowes laminator only for its intended purpose of laminating documents according to the indicated specifications. 4. Extreme caution should be taken when the appliance is used by or near children or invalids. 5. Do not insert anything in the throat opening of the machine other than carriers with pouches/documents. 6. Do not attempt to remove jammed materials by poking objects into the laminator and particularly do not insert any metal objects such as a letter opener, knife, scissors, paper clips etc., into the laminator. 7. Do not service this product yourself. Opening/removing covers may expose you to dangerous voltage points or other risks, and may void manufacturer’s warranty. 8. Place unit in a secure, stable work area to prevent the machine from falling and possibly causing personal injury and damage to the laminator. 9. Wipe exterior only with a damp cloth only when unplugged. Do not use near water. Do not use detergents or solvents. 10. The laminator is intended for indoor use only. 11. Turn laminator off when not in use for an extended period of time. 12. Use laminator in close proximity to electrical outlet. Product must be easily accessible when plugged into outlet. GXL 1256 3 2 1 5 4 Electrical Safeguards 1. The Foam Board Laminator must be connected to a supply voltage corresponding to the electrical rating of the machine as indicated. 2. Unplug the laminator before moving it, or when it is not in use for an extended period of time. 3. Do not let cord hang over edge of counter, or touch hot surfaces. 4. Do not operate the laminator with a damaged cord or plug, or after the laminator malfunctions, has been dropped or is damaged in any manner. Please call customer service at 1-800-945-4545 for information on repairs or adjustments. 5. Do not overload electrical outlets beyond their capacity as this can result in fire or electrical shock. 6. Do not alter attachment plug. Plug is configured for the appropriate electrical supply. A B C Operation A key feature and added benefit of the GXL 125 allows you the versatility of laminating both Foam Boards and Hot Pouches. To Start • Place the laminator on a sturdy, flat work surface. Allow ample clearance behind the laminator for laminated items to exit completely. • Plug the laminator into a power source that matches the laminator’s rate of voltage. NOTE: Fluctuating voltage may cause inconsistent lamination or mechanical problems with the laminator. If you suspect voltage problems, use a voltage stabilizer. For Use With Foam Boards 1. Before turning power switch on, verify that the Foam Board\Pouch Selector is positioned correctly in the “Foam Board” location. 2. Turn power on by positioning On/Off switch in the “Heat Only” location. This will allow the machine to pre-heat without engaging the laminating rollers. NOTE: During first usage, a small white puff of smoke may appear which is common to a new laminator. 3. Adjust temperature control to the foam board setting. 4. Wait 2-3 minutes for green ready light to illuminate. This indicates laminator is ready for use. 5. Place item to be laminated onto a Fellowes’ foam board by raising laminate cover sheet and inserting document. Center the item for an even border; a border of approximately 1/8" to 1/4" is recommended. 6. Initiate laminating rollers by moving selector to “Heat and Rollers” setting. 7. Insert the foam board, sealed edge first, slowly into the front loading area of the laminator until it engages with the machine. NOTE: Heat source located on top of machine. For best results, feed foam board with item to be laminated facing top. 8. The finished laminated item will automatically exit at the rear of the machine. After the foam board has stopped moving, place it on a flat surface and allow to cool for one minute. 9. Mount easel or hang tab to back of foam board, if desired. 10. Turn the laminator off and unplug after completion of usage. For Use With Hot Pouches 1. Before turning power switch on, verify that the Foam Board\Pouch Selector is positioned correctly in the “Pouch” location. 2. Turn power on by positioning On/Off switch in the “Heat Only” location. This will allow the machine to pre-heat without engaging the laminating rollers. NOTE: During first usage, a small white puff of smoke may appear which is common to a new laminator. 3. Adjust the temperature control to correspond with pouch thickness. 4. Wait 2-3 minutes for green ready light to illuminate. This indicates laminator is ready for use. 5. Place item to be laminated into a Fellowes’ laminating pouch. Center the item for an even border; a border of approximately 1/8" to 1/4" is recommended. 6. Place pouch into carrier. (Optional, but recommended) 7. I...