Оценок - 5, средний балл: 4
(
)
)
|
Фрагмент инструкции
Do not operate processor for more than one minute at a time. If processing large quantities, let the processor rest about one minute before continuing. • To slice or shred cheese, select a firm cheese like cheddar, Monterey Jack, or Swiss. Place cheese in freezer for 30 minutes before processing. Always use highest speed of food processor. Parts and Features 1 2 3 4 5 6 7 Food Pusher Food Chute Food Gate – leave in cover for regular processing; remove for continuous processing. Continuous Feed Chute Reversible Slicing/Shredding Disc Motor Shaft Base 8 9 10 11 12 13 14 Pull-Out User Guide Control Panel Bowl Continuous Feed Disc – must be used for continuous processing; this disc “throws” the food through the Continuous Feed Chute. S-Blade Dosing Cup (see inset) Cord Storage 1 2 3 4 5 6 7 8 9 10 11 12 13 13 14 Using Your Food Processor NOTES: • Always lock the bowl onto base before putting on any blade or disc. Make sure blade or disc is securely in place before using. • With this food processor you can use the continuous feed chute for slicing and shredding into a separate container. The continuous feed chute allows slicing or shredding foods not limited to the processor bowl capacity. Hints! • The bowl will hold 9 cups of dry ingredients or 2 cups of liquid. Do not overfill. • Do not use your food processor to crush ice. • For consistent texture, foods should be cut into 1-inch cubes before mincing or chopping with the S-blade. How to Lock the Bowl Place the bowl on processor base and turn counterclockwise until the bowl locks into place. NOTE: The food processor will not work unless the bowl is locked. How to Lock the Cover Place cover on bowl and turn the cover counterclockwise until the cover locks into place. NOTE: The food processor will not work unless the cover is locked. Tip! When the bowl and the cover are properly locked and the unit is plugged in, the Ready light should be on. Processing with the Slicer/Shredder • To slice or shred cheese, select a firm cheese like cheddar, Monterey Jack, or Swiss. Place cheese in the freezer for 30 minutes before processing. Always use the highest speed of food processor. • The Reversible Slicer/Shredder Disc has a slicing blade on one side and shredding teeth on the other. Place on motor shaft with desired cutting edge facing up. • To prepare julienne vegetables, slice then remove from bowl and restack the vegetables. Pack into food chute with slices vertical. Slice again to make matchstick cut vegetables. 1. Make sure the Control Switch is turned OFF and the unit is unplugged. 2. Lock the bowl onto base. (See “How to Lock the Bowl” on page 5.) 3. Put Slicer/Shredder Disc on motor shaft with the desired side facing up for either slicing or shredding. Lock cover onto bowl. (See “How to Lock the Cover” on page 5.) Slicer/Shredder Disc 4. Cut food to fit food chute. Pack food chute tightly with food. Insert food pusher in chute. Always use the food pusher to feed food into the chute. NEVER PUSH FOOD THROUGH CHUTE WITH HANDS. 5. Plug in unit and process food. 6. Select speed. While pressing on food pusher, push ON or PULSE to process food. 7. When food chute is empty, push OFF or release from PULSE position. Wait until blade has stopped rotating before removing cover. Motor Shaft How to Operate the Controls On/Off Speed Dial Pulse The controls are conveniently located on top of the base. Rotate the center knob to select a Low, Medium, or High variable speed. If the bowl and cover are properly locked the Ready light should be on. The S-blade can be used to coarsely chop, finely mince, mix, or puree food to a smooth consistency. 1. Make sure the Control Switch is turned OFF and the unit is unplugged. 2. Lock the bowl onto base. (See “How to Lock the Bowl” on page 5.) 3. Place the S-blade onto motor shaft of food processor in center of bowl. Turn slowly until blade drops into place. Handle carefully; the blade is sharp. Processing with the S-Blade 4. Lock cover onto bowl. (See “How to Lock the Cover” on page 5.) Insert food pusher into food chute. 5. Pull all of cord out of cord storage. This will help air flow and keep the motor cool. Plug in unit and process food. The processing speed and time will determine the finished consistency of the food. The Pulse button can help you avoid overprocessing. S-Blade Motor Shaft IMPORTANT: When using the continuous feed chute the food gate must be removed and the continuous feed disc must be in place. 1. Make sure the Control Switch is turned to OFF and the unit is unplugged. 2. Lock the bowl onto base. (See “How to Lock the Bowl” on page 5.) 3. Place the continuous feed disc, ribbed side up, onto the motor shaft. Turn the disc slowly until it drops into position (level with top of bowl). Continuous Processing Continuous Feed Disc Motor Shaft 4. Select desired side of reversible slicing/shredding disc and place that side up on the motor shaft. Slicer/Shredder Disc 5. REMOVE FOOD GATE FROM CONTINUOUS FEED COVER TO PREVENT DAMAGE ...