Оценок - 3, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Note: If the power supply cord is damaged, it should be replaced by qualified personnel. In Latin America, by an authorized service center. 1284CUPS Product may vary slightly from what is illustrated. . . . . . . . . . . A1 1. Mounted unit † 2. Grinding bowl (Part # CG001) † 3. Stainless steel grinding blade (Part # CG002) 4. ON/OFF pulse control button 5. Coffee grinder cup selection button 6. Coffee grinder coarseness selection button † 7. Processing workbowl (Part # CG003) † 8. Stainless steel chopping blade (Part # CG005) † 9. Storage lid (Part # CG004) 10. Cord storage (not shown) 11. Cord management hook (not shown) † 12. Mounting kit (Part # CG006-01) white, (Part # CG006-02) black (not shown) Note: † indicates consumer replaceable/removable parts B A C A2 † 1. Mounting Parts (Part # SDC-MOUNTING KIT) A. 16 Spacers 4 ." 4 ." 4 3/16" 4 1/16" B. 12 Screws 4 1" 4 1." 4 2." C. 4 Washers 2. Mounting Template (in box) You will also need: • Tape • Ruler (or you may cut out the ruler provided on the template) • Electric drill with a .” drill bit GETTING STARTED • Remove all packing material, labels and any stickers. • Remove and save literature. • Unpack mounting parts and set them aside in a safe place where they will not roll away or get lost. Important: Do not attempt to operate appliance until it is properly installed. CHOOSE A LOCATION When choosing your location, consider the following: • DO make sure to mount within reach of an electrical outlet. • DO consider your normal work patterns in the kitchen when choosing location. • DO NOT mount over any heating or cooking appliance such as your range or oven. • DO NOT mount over or near a sink. • DO NOT mount under, in front of or behind any under-cabinet light fixtures. Note: If mounting multiple †SpaceMaker™ appliances and you are installing your appliance next to the SpaceMaker™ oven (Fig. A.3): • Allow at least 1” between the control panel side of the oven and the appliance. • Allow at least 4” between the side opposite the control panel of your oven and adjacent wall or other appliance. You can mount the other appliances flush to one another. 4”1” 4” 1” A.3 Note: If you are connecting this appliance to the receptacle of another †SpaceMaker™ appliance such as the toaster oven or coffeemaker, make sure you can easily unplug the appliance following use. DETERMINE CABINET TYPE Prior to installation, determine if your cabinet has a flat bottom (B) or an overhang molding (C). If your cabinet is flat, follow STANDARD INSTALLATION; if the cabinet has an overhang molding, refer to OVERHANG MOLDING INSTALLATION. STANDARD INSTALLATION (FLAT CABINET) Important: Always wear protective glasses or goggles to prevent injury when drilling. 1. Clear countertop under installation area to avoid getting dust or debris on other appliances or items. Open cabinets and remove contents to make mounting easier. 2. Clean both the underside and topside of the bottom panel of the cabinet. 3. With cabinet doors open, place mounting template flush against the surface of the underside of your cabinet, making sure to align thick line on template with bottom front edge of your cabinet (D). Important: Do not align screw holes on template directly under the partition between cabinets, as this will prevent you from installing the appliance properly. Pay close attention to where the drill holes will be set so as not to damage your cabinets during mounting. Drilling through your cabinet’s partition may cause damage to cabinets and prevent proper installation. 4. Fold the template along the edge of your cabinet so the thick line is straight with bottom front edge; pull template tight and tape down to hold in place. 5. Drilling from under the cabinet up, drill holes through the 4 places marked on the template, using a .-inch drill bit (E). Important: Always ensure you are drilling straight up through the marked mounting holes on the template. Drilling at an angle may prevent proper installation and may damage cabinets if the drill bit pierces the partition. 6. Once holes are drilled, remove tape and mounting template. 7. Wipe dust and debris off the topside and underside of the cabinet surface. 8. Place a washer inside the cabinet over each of the 4 holes you drilled. 9. Hold appliance in place, aligning front of unit with front edge of cabinet; drilled holes on cabinet should be aligned with mounting holes on the unit. 10. Drop one of your screws through each of the washers covering the holes in the cabinet, from inside the cabinet down. Note: To determine which screws to use, you must have enough of the screw exposed underneath the cabinet to properly thread the screw into the nut. 11. Screwing from inside the cabinet down into appliance holes, tighten 4 screws in place to secure appliance to cabinet. Note: Always tighten screws to ensure the appliance does not move or shake during operation. 12. Pull out cord from cord storage behind appliance and plug into standard electrical outlet. Extra...