Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
Correction: Check for proper position of the Electrode Tip as shown in Figures 8e and 10. The gap between the Spark Electrode Tip and Burner or Spark Receiver should be approximately 3/16", adjust if necessary. With the gas supply closed and all Control Knobs set to OFF press the Electric Ignitor Cap and check for the presence of a spark at the Electrode. • Disconnected Ignition Wires Correction: Inspect the Ignitor Junction Box found behind the Control Panel. Connect loose Ignitor wires to Junction Box and try to light the grill. • Weak AA battery Correction: Unscrew the Ignitor Cap and replace the battery. 4. If the grill still does not light you may need to purge air from the gas line or reset the regulator excess gas flow device. Note: This procedure should be done every time a new LP gas tank is connected to your grill. To purge air from your gas line and/or reset the regulator excess gas flow device: • Turn the Control Knobs to the OFF position. • Turn off the gas at the tank valve. • Disconnect regulator from LP gas tank. • Let unit stand for 5 minutes. • Reconnect regulator to the LP gas tank. • Turn the tank valve on slowly until 1/4 to 1/2 open. • Open the Gdll Lid. • Set Control Knobs to OFF Push and turn the LEFT Control Knob to HIGH. . If all checks or corrections have been made and you still have questions about operating your gas grill, call the Customer Service Helpline 8am -8pm CST, Monday through Friday at 1-888-317-7642. Z WARNING Should a "FLASHBACK" fire occur in/or around the Burner Tubes, follow the instructions below. Failure to comply with these instructions could result in a fire or explosion that could cause serious bodily injury, death, or property damage. • Shut off gas supply to the gas grill. • Turn the Control Knobs to OFF position. • Put out any flame with a proper fire extinguisher. • Open Grill Lid. • Once the grill has cooled down, clean the Burner Tubes and Burners according to the cleaning instructions found on page 28 in this manual. 26 CAUTION: BesureyourgrillisOFFandcootbeforecleaning. Takecarenotto chiporscratchthepaintedsurfaces becauseit willvoidyourwarrantyagainstrusting. Aswithallappliances,propercareandmaintenance willkeepyourgrillintopoperatingconditionand prolongitslife.Byfollowingthesecleaningproceduresonatimelybasis, yourgrillwillstaycleanandworkproperlywithminimumeffort. Cleaning The Cooking Grids Before initial use and periodically we suggest you wash your Cooking Grids in a mild soap and warm water solution. You can use a wash cloth or vegetable brush to clean your Cooking Grids. Cleaning The Flame Tamers Periodically you should wash the Flame Tamers in a soap and warm water solution. Use a vegetable brush to remove stubborn burnt-on cooking residue. Dry the Flame Tamers thoroughly before you reinstall them into the cooking bowl. Cleaning The Grease Tray and Receptacle To reduce the chance of fire, the Grease Draining Tray and Grease Receptacle should be visually inspected before each grill use. Remove any grease and wash Grease Tray and Receptacle with a mild soap and warm water solution. Annual Cleaning of The Grill Interior Burning-off the grill after every cookout will keep it ready for instant use. However, once a year you should give the entire grill a thorough cleaning to keep it in top operating condition. Follow these steps: 1. Turn all Burner Valves to the full OFF position. 2. Turn the LP gas tank valve to the full OFF position. . Disconnect the regulator from the gas tank. Inspect the hose with regulator assembly for cracking, cuts or any other damage, and replace as neccessary with Sears replacement parts. See Parts List. 4. Remove and clean the Flame Tamers, Cooking Grids, Cooking Rack and Grill Burners. . Cover each Gas Valve Orifice with aluminum foil. 6. Brush the inside and bottom of the grill with a fiber pad or nylon brush, and wash with a mild soap and warm water solution. Rinse thoroughly and let dry. 7. Remove aluminum foil from Orifices and check each Orifice for obstruction. 8. Check each Spark Electrode, adjusting as needed. The space between the Spark Electrode Tip and Spark Receiver should be approximately 3/16". g. Replace the Burners and adjust the Gas Collector Box. The edge of the collector box should be overlapping the Burner Port. 10. Replace Flame Tamers and the Cooking Grids. 11. Reconnect the gas source and observe the Burner flame for correct operation. Cleaning Exterior Surfaces: Before initial use, and periodically thereafter, we suggest you wash your grill using a mild soap and warm water solution. You can use a wash cloth or sponge for this process. Do not use a stiff wire or brass brush that might remove paint during the cleaning process. Cleaning Exterior Stainless Steel Surfaces: Weathering and extreme heat can cause exterior stainless steel surfaces to turn tan in color. Machine oils used in the manufacturing process of stainless steel can also cause this tanning color. After removing the protective PVC film ...
Эта инструкция также подходит к моделям:Кухонные комбайны - 141.15337 (2.16 mb)