Оценок - 3, средний балл: 4.7
(
)
)
|
Фрагмент инструкции
The saw is equipped with a water resistant 3 HP electric motor and direct gear drive transmission that provides a blade speed of 3500 feet per minute. The carriage (Fig.1) has stainless steel ball bearings providing easy travel and dependability. The shaped front edge of the carriage is comfortable to the operator's body even when leaned on during movement. The carriage lock is standard. The upper pulley cover and baffle (Fig. 1) are standard in durable plastic, optional in stainless steel. Table, carriage, pulleys, guides, and wiper assemblies can be quickly removed without tools for ease of cleaning. Moving parts are enclosed but accessible. The blade is guarded above and below the cutting zone. The pusher plate is provided to eliminate the need of handling items close to the blade; it can ride on the right "flanged-end" of the carriage so you keep your hands away from the cutting edge of the blade. For electrical specifications above 250 volts, a transformer provides a 115 volt control circuit voltage. Thermal overload protection is an option. One long-life blade is furnished with each saw as standard equipment. This blade cannot be resharpened; replacement blades are available through your local Hobart Service Office. UPPER PULLEY COVER (SST) SWITCH KNOB COLUMN GUARD UPPER GUIDE AND GUARD TABLE (LEFT) GAUGE PLATE TABLE (RIGHT) CARRIAGE SAW BLADE GAUGE PLATE HANDLE LOCK LEVER CARRIAGE LOCK LOWER COVER (SCRAP PAN) LEGS FEET PL-40830-1 Fig. 1 © HOBART CORPORATION, 1995 –2– INSTALLATION UNPACKING AND ASSEMBLY Immediately after unpacking the meat saw, check for possible shipping damage. If the meat saw is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installation, test the electrical service to make sure it agrees with the specifications on the machine data plate located on the column. Packed in a packet attached to the table compartment are the pusher plate and the gauge plate handle. Place the pusher plate in its storage location under the carriage support (Fig. 2). Assemble the gauge plate handle to the gauge plate support by screwing the stud into the threaded hole (Fig. 3). LEVELING Place the saw in its operating location. Using a spirit level, level the meat saw front-to-back and side- to-side by turning the threaded feet in or out. PL-40847-1 GAUGE PLATE HANDLE PL-40831-1 HAND KNOB CARRIAGE SUPPORT SAW BLADE CARRIAGE PUSHER PLATE Fig. 2 Fig. 3 WARNING: DISCONNECT ELECTRICAL POWER AND PLACE A TAG AT THE DISCONNECT SWITCH INDICATING THAT YOU ARE WORKING ON THE CIRCUIT. SAW BLADE The saw blade must be installed so the teeth point to the right and down (Fig. 4). UPPER GUIDE AND GUARD ASSEMBLY When the saw is off, the hand knob (Fig. 4) can be used to raise or lower the upper guide and guard assembly so the cutting zone is only as high as necessary for the piece being cut. The hand knob is not loosened during raising or lowering — it should remain tightly secure. Fig. 4 PL-52107 Hand Knob Upper Guide and Guard –3– LOWER GUIDE BLADE BLOCK SAW BLADE BLADE SCRAPERS LOWER GUIDE BLADE BLOCK SAW BLADE BLADE SCRAPERS UPPER PULLEY COVER (Plastic - Standard) The plastic upper pulley cover (Fig. 5) should be installed on the two hinge-retainers at the top and securely latched at the bottom during use. To remove the plastic upper pulley cover for cleaning, release the latch at the bottom and remove from the hinge-retainers at the top. UPPER PULLEY COVER (Stainless Steel - Optional) The stainless steel upper pulley cover (Fig. 1) should be installed on the two hinge pins of the stainless steel upper pulley baffle and securely latched during saw use. To remove the stainless steel upper pulley cover for cleaning, unlatch and open the stainless steel upper pulley cover; then, lift straight up off the hinge pins. LOWER COVER (Scrap Pan) During use, the lower cover (Fig. 5) acts as a scrap pan, accumulating bone dust and debris from the blade scrapers and pulley wiper that are located on the lower panel (Fig. 6). To remove the lower cover (scrap pan) for cleaning, release the clip at the top; pull out and lift the lower cover from the groove at the bottom of the lower panel. UPPER PULLEY COVER (PLASTIC) COLUMN GUARD LOWER COVER (SCRAP PAN) CARRIAGE LOCK CARRIAGE TENSION ADJUSTER PULLEY WIPER Fig. 5 Fig. 6 BLADE SCRAPERS Two blade scrapers wipe the blade during sawing to accumulate bone dust and debris inside the lower cover (scrap pan). The left scraper points up and the right scraper points down (Fig. 6). After the blade is removed, the scrapers can slide off their mounting blocks for cleaning. PULLEY WIPER The pulley wiper (Fig. 6) scrapes bone dust or debris from the lower pulley during use. The pulley wiper can be removed for cleaning by springing the wiper up and sliding it off the pins. –4– PL--40833-1 PL-40848-1 UPPER AND LOWER PULLEYS The upper and lower pulleys are assembled on the upper and lower pulley shafts; the latch on each pulley should be seat...