Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
. with Portion Scale MODEL 2912PS ML-104966 Previous models covered by this manual: 2912PS ML-104833 701 S. RIDGE AVENUE TROY, OHIO 45374-0001 937 332-3000 FORM 34456 (Feb. 2000) © HOBART CORPORATION, 1999 – 2 – Installation, Operation, and Care of Model 2912PS Automatic Slicer with Portion Scale SAVE THESE INSTRUCTIONS GENERAL The model 2912PS Automatic Slicer with Portion Scale can display the weight or slice count as the sliced product falls to the platter. Six preset values can be programmed for lb weigh, oz weigh, and slice count, which are readily accessible for portioning. Other values can be manually preset before beginning an automatic cycle. The scale display can Tare to indicate Net weight but is NOT LEGAL FOR TRADE. An automatic cycle stops slicing when the preset value is satisfied (by net weight or slice count). The model 2912PS is equipped with a 1.2 HP motor and is available for single-phase electrical service. The slicer features the exclusive Hobart Stay-Sharp contoured cast solid stainless steel knife. The slicer is furnished with a cord and plug as standard equipment. The 2912PS slicer features automatic slicing with six adjustable speeds. Other features and options include: The Power Interrupt feature, standard, requires the slicer to be manually re-started after a power interruption. The Gauge Plate and Carriage Interlock feature, standard, prevents the Carriage Tray from being removed unless the Carriage is in the HOME position (pulled all the way to the front) and the Gauge Plate is CLOSED. When the Carriage Tray is tilted horizontally, the slicer will turn OFF if it has not previously been turned OFF. Once the Carriage Tray is tilted horizontally or removed, the slicer cannot be started and the Gauge Plate cannot be opened until the Carriage Tray is returned to its normal operating position. The HomeStart feature, standard, requires the carriage to be in the HOME position before the slicer can be started. The AutoShutoff feature, provided on all 2912PS slicers, is turned off at the factory but can be enabled or disabled by pressing the down arrow key while pulling the switch knob all the way forward with the lever on manual. If AutoShutoff is enabled, the slicer will turn off if a keystroke or full stroke of the carriage has not been made within a 10 second interval while in Manual mode. A tubular food chute, and a 4" leg set are available accessories for 2912PS. The low carriage fence is standard on 2912PS. A high carriage fence is an accessory used with front mounted meat grips. The standard meat grip is front-mounted. Heavy front-mounted meat grip is an available accessory. In Automatic Mode, the operator selects WEIGH (by LB or OZ units) or COUNT mode and a PRESET value. As each slice is made, the remaining slice count or actual weight displays. The slicer stops when the PRESET value is met. The weight or count setting is retained in memory for repeat applications or can be reset. If a PRESET value was not selected, the slicer begins at zero, displays the actual weight or slice count, and slices continuously until stopped by the operator. When all Automatic Mode requirements are met, you can press the Slice / Pause button to either start or resume automatic slicing or to stop slicing and return to the Home position. Refer to pages 6 – 9 for details. – 3 – INSTALLATION UNPACKING Immediately after unpacking the slicer, check for possible shipping damage. If the slicer is found to be damaged, save the packaging material and contact the carrier within 15 days of delivery. Prior to installing the slicer, test the electrical service to assure it agrees with the specifications on the machine data plate. The data plate is located on the right side of the slicer base. CARRIAGE TRAY The Carriage Tray is secured to the slicer when the knob on the Carriage Tray / Support Arm is turned clockwise until snug (Fig. 1). Refer to page 11 for assembly information. SHARPENER The Sharpener should already be mounted on top of the slicer and locked to its bracket (Fig. 1). TOP KNIFE COVER The Top Knife Cover should already be in place and secured with its Latch Knob (Fig. 1). DEFLECTOR The Deflector should already be mounted below the knife (Fig. 1). FENCE (Low and High Fences are used with front-mounted meat grip only.) Either Fence (Fig. 1) can be clamped on the Carriage Tray to limit product movement during slicing. Model 2912PS Slicer TOP KNIFE COVER CARRIAGE TRAY CARRIAGE TRAY / SUPPORT ARM FENCE Fig. 1 1. Back out Thumb Screw.Lay Fence on Carriage Tray. Rotate to Vertical. SHARPENER DEFLECTOR 2. 3.Slide Fence Up. Tighten Screw. PL-41414-1 ELECTRICAL WARNING: THIS MACHINE IS PROVIDED WITH A THREE-PRONG GROUNDING PLUG. THE OUTLET TO WHICH THIS PLUG IS CONNECTED MUST BE PROPERLY GROUNDED. IF THE RECEPTACLE IS NOT THE PROPER GROUNDING TYPE, CONTACT AN ELECTRICIAN. CLEAN BEFORE USING The 2912PS slicer must be thoroughly cleaned and sanitized after installation and before being used...
Эта инструкция также подходит к моделям:Кухонная посуда - 2912PS ML-104833 (2.39 mb)