Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
If the blade is not 0° to the miter table: Figure 9 3. Using a 5mm hex wrench, loosen four adjustment bolts (B, Fig. 9) at the back of the miter saw. Unlock the bevel lock handle (A, Fig. 8) and position the cutting arm to be zero degrees to the table using the combination square as your reference. 4. Tighten the bevel lock handle (A, Fig. 8) and the four adjustment bolts (B, Fig. 9). Bevel Scale Indicators 1. Set the blade to be exactly 90°(0°) to the table. 2. With cross-point screwdriver, loosen two bevel indicator screws (C, Fig. 9). 3. Adjust bevel indicators (D, Fig. 9) to the “0” mark on the bevel scale and retighten the screws (C, Fig. 9). 45° Left Bevel Positive Stop Adjustment 1. Set the miter angle to zero degrees. Fully extend the sliding fence completely to the left then pull the bevel detent pin (E, Fig. 10) out. Note: When retracting the bevel detent pin, it may be required to slightly shift the upper arm assembly right or left. 16 A Figure 8 B B Figure 10 C D E Figure 11 2. Loosen the bevel lock handle (A, Fig. 8) and tilt the cutting arm completely to the left (Figure 11). 3. Using a combination square, check to see if the blade is 45° to the table. 4. To adjust, tilt the cutting arm to zero degrees, loosen the lock nut (B, Fig. 12) and turn the stop bolt (A, Fig. 12) in or out accordingly. 5. Tilt the cutting arm back to the left and recheck alignment. 6. Repeat steps 1–4 if necessary until the blade is 45° to the table, then tighten the lock nut (B, Fig. 12) to secure the stop bolt (A, Fig. 12). 45° Right Bevel Positive Stop Adjustment 1. Set the miter angle to zero degrees. Fully extend the sliding fence completely to the right then pull the bevel detent pin (E, Fig. 12) out. Note: When retracting the bevel detent pin, it may be required to slightly shift the upper arm assembly right or left. 2. Loosen the bevel lock handle (A, Fig. 8) and tilt the cutting arm completely to the right (Figure 13). 3. Using a combination square, check to see if the blade is 45° to the table. 4. To adjust, tilt the cutting arm to zero degrees, loosen the locknut (D, Fig. 12) and turn the stop bolt (C, Fig. 12) in or out accordingly. 5. Tilt the cutting arm back to the right and recheck alignment. 6. Repeat steps 1–4 if necessary until the blade is 45° to the table, then tighten the lock nut (D, Fig. 12) to secure the stop bolt (C, Fig. 12). 33.9° Left & Right Bevel Adjustment 1. Set the miter angle to zero degree. Fully extend both sliding fences. 2. Loosen the bevel lock handle (A, Fig. 8). 3. Tilt the cutting arm to the 33.9° left bevel position and engage the positive stop by pushing the bevel detent pin (E, Fig. 12) in. 4. Using a combination square, check to see if the blade is 33.9° to the table. 5. To adjust, turn the setscrew (A, Fig. 14) in or out with a 6mm hex wrench until the blade is 33.9° to the table. 6. Repeat steps for the right bevel 33.9. bevel adjustment, making adjustments to setscrew B, Fig. 15. Figure 12 Figure 13 Figure 14 Figure 15 17 Miter Angle The sliding compound miter saw scale can be easily read, showing miter angles from 0° to 45° to the left, and 0° to 60° to the right. The miter saw table has ten of the most common angle settings with positive stops at 0°, 15°, 22.5°, 31.6°, and 45° and 60° right. These positive stops position the blade at the desired angle quickly and accurately. Follow the process below for quickest and most accurate adjustments. Referring to Figure 16: 1. Lift up on the quick-cam miter table lock (A) to unlock the table. 2. Lift up on the positive stop locking lever (C) and move the turntable with handle (B) to align the indicator (D) to the desired degree measurement. 3. Lock the table into position by pressing down on the quick-cam miter table lock (A). Miter Scale Indicator Adjustment 4. Move the table to the 0° positive stop. 5. Loosen the screw (E) that holds the indicator with a screwdriver. 6. Adjust the indicator (D) to the 0° mark and retighten screw. Adjusting Fence Squareness 1. Loosen four fence locking screws (D, Fig. 18). Note: two locking screws to each fence. 2. Lower the cutting arm and lock in position. 3. Using a square (B, Fig. 17), lay the heel of the square against the fence (C, Fig. 17) and the ruler against the blade (A, Fig. 17). 4. Adjust the fence 90° to the blade and tighten the four fence locking screws. If the saw has not been used recently, recheck blade squareness to the fence and readjust if needed. 5. After fence has been aligned, using a scrap piece of wood, make a cut at 90. then check squareness on the piece. Readjust if necessary. Figure 16 Figure 17 Figure 18 18 Positive Stop Miter Angle Adjustment Referring to Figure 19: 1. Unlock the miter table by lifting up on the quick- cam miter table lock (A). 2. Raise the positive stop locking lever (C) up; at the same time grasp the miter handle (B) and rotate the miter table left or right to the desired angle. 3. Release the positive stop locking lever (C) and set the mite...