Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
OPERATING THE COUPLER Your powerhead is equipped with a coupler which enables optional attachments to be installed. The optional attachments are: Edger ............. 71-51157 Blower ............ 71-51160 Pruner ............ 71-51161 Brushcutter* ....... 71-51159 *not designed for use with electric powerheads _ WARNING: Always disconnect powerhead spark plug (or disconnect powerhead from power source) before removing or installing attachments. REMOVING ATTACHMENT CAUTION: When removing or instal ling attachments, place the power- head and attachment on a flat surface for stability. 1. Loosen the coupler by turning the knob counterclockwise. Hanger Shaft Tine Guard TINE GUARD The TINE GUARD provides partial protection from the rotating tines. Upper Shaft Coupler Lower Attachment TIGHTEN Knob 2. Press and hold the locking/release button. Locking/Release Button Upper Shaft Lower Attachment 3. While securely holding the upper shaft, pull the attachment straight out of the coupler. INSTALLING ATTACHMENT 1. Remove the shaft cap from the attachment (if present) and discard. 2= Position locking/release button of attachment into guide recess of upper shaft coupler. Coupler Primary Hole Guide Recess Upper Locking/ Attachment Shaft Release Button 3= Push the attachment into the coupler until the locking/release button snaps into the primary hole. 4= Before using the unit, tighten the knob securely by turning clockwise. INSTALLING ATTACHMENT HANGER An attachment hanger is provided for storage when attachment is not in use. To install hanger on attachment: 1= Remove the shaft cap from the attachment (if present) and discard. 2= Press and hold the locking/release button. 3= Push hanger onto the attachment until the locking/release button snaps into the hole. OPERATING POSITION ALWAYS WEAR: _Eye Protection Long Pants Heavy Shoes 4HIWARNING: To avoid personal injury, never carry the cultivator while the unit is running. _WARNING: The gearbox gets very hot after extended periods of use. To avoid burns, do not touch the gearbox until it has been allowed to cool. CULTIVATING 1. Move the cultivator to the work area prior to starting the engine/motor. 2. With the engine/motor running and the tines off the ground, press the throttle trigger to increase the engine speed. 3. Hold trigger handle and assist handle firmly. Slowly lower the cultivator until the tines make contact with the ground. 4. As unit begins cultivating, pull back on the unit so that the tines can penetrate the ground. 5. Once the ground has been broken, continue at a moderate pace until you are familiar with the controls and the handling of the cultivator. 6. Pull the cultivator backwards to improve the depth of cultivation and reduce your effort. 7. To cultivate in confined areas or narrow rows, remove the left and right outer tines (see TINE REPLACEMENT). MAINTENANCE SCHEDULE WARNING: Always stop unit and nect powerhead from power source) CARE AND MAINTENANCE TASK Check for loose fasteners and parts Check for damaged or worn parts Inspect and clean unit and decals Check or replace tines GENERAL RECOMMEN DATIONS The warranty on this attachment does not cover items that have been subjected to operator abuse or negli gence. To receive full value from the warranty, the operator must maintain the cultivator attachment as instructed in this manual. CHECK FOR LOOSE FASTENERS AND PARTS , Clevis pins • Hitch pin clips CHECK FOR DAMAGED OR WORN PARTS Contact Sears Service Center for re placement of damaged or worn parts. • Tine Guard -Discontinue use of cultivator if tine guard is damaged. INSPECT AND CLEAN UNIT AND DECALS • After each use, inspect complete unit for loose or damaged parts. Clean the unit and decals using a damp cloth with a mild detergent. • Wipe off unit with a clean dry cloth. disconnect spark plug wire (or disconbefore performing maintenance. WHEN TO PERFORM Before each use Before each use After each use Every 5 hours of operation TINE MAINTENANCE _,WARNING: The tines will contin ue to spin after the engine stops or af ter the throttle trigger has been released. To avoid serious injury, make sure the tines have stopped coasting and disconnect the spark plug (or dis connect powerhead from power source) before performing work on the tines. '_WARNING: Always replace tines that are bent, warped, cracked, broken, or damaged in any other way. Never attempt to straighten and reuse a damaged tine. Use only specified replacement tines. Wear protective gloves when handling or performing maintenance on the tines to help avoid injury. TINE REPLACEMENT ,_WARNING: The tines will contin ue to spin after the engine stops or after the throttle trigger has been released. To avoid serious injury, make sure the tines have stopped coasting and disconnect the spark plug (or disconnect powerhead from power source) before performing work on the tines. ,I_WARNING: Wear protective gloves when handling or performing maintenance on the tines to avoid injury. The tines become ve...
Эта инструкция также подходит к моделям:Культиваторы - 51158 (321.61 kb)
Культиваторы - 944.511580 (321.61 kb)