Оценок - 4, средний балл: 3.3
(
)
)
|
Фрагмент инструкции
Prevent fires! Keep the engine free of grass, leaves, spilled oil, or fuel. Re move fuel from tank before tipping unit for maintenance. Clean muffler area of all grass, dirt, and debris. Do not touch hot muffler or cylinder fins as contact may cause burns. ENGINE LUBRICATION Use only high quality detergent oil rated with API service classification SG-SL. Select the oil’s SAE vis cos i ty grade according to your expected temperature. NOTE: Although multi-viscosity oils (5W-30, 10W-30, etc.) improve starting in cold weather, these multi viscosity oils will result in increased oil consumption when used above 32°F (0°C). Check your engine oil level more frequently to avoid possible engine damage from running low on oil. Change the oil after every 50 hours of operation or at least once a year if the tiller is not used for 50 hours in one year. Check the crankcase oil level before starting the engine and after each eight (8) hours of continuous use. Add SAE 30 motor oil or equivalent. Tighten oil filler plug securely each time you check the oil level. MAINTENANCE TO CHANGE ENGINE OIL (See Fig. 13) NOTE: Before tipping tiller to drain oil, empty fuel tank by running engine until fuel tank is empty. 1. Disconnect spark plug wire from spark plug and place wire where it cannot come in contact with plug. 2. Remove engine oil cap; lay aside on a clean surface. 3. Tip tiller on its side as shown and drain oil into a suitable container. Rock tiller back and forth to remove any oil trapped inside of engine. 4. Wipe off any spilled oil from tiller or side of engine. 5. Slowly pour oil down the oil fill spout, stopping every few ounces to check the oil level with the dipstick. 6. Stop adding oil when you reach the FULL mark on the dipstick. Wait a minute to allow oil to settle. 7. Continue adding small amounts of oil, rechecking the dipstick until oil level settles at FULL. DO NOT overfill, or engine will smoke heavily from the muffler on startup. 8. Always be sure to retighten oil dipstick before starting engine. 9. Re con nect spark plug wire to spark plug. SPARK PLUG WIRE CONTAINER Fig. 14 AIR FILTER Your engine will not run properly and may be damaged by using a dirty air filter. Clean the element after every 25 hours of operation or every season. Replace the air filter every season. Service air cleaner more often under dusty conditions. TO CLEAN AIR FILTER ELEMENT 1. Remove screw. 2. Re move air cleaner carefully to pre vent dirt from en tering carburetor. 3. Take air cleaner apart and clean air filter element. 4. Wash filter element in liquid de ter gent and water. 5. Wrap filter element in cloth and squeeze dry. 6. Lightly coat filter element with clean engine oil. Squeeze in towel to re move excess oil. Do not satu rate. 7. Reassemble parts and put back on carburetor. CUP BODY ELEMENT ASSEMBLE SO LIP EXTENDS OVER EDGE OF AIR CLEANER BODY LIP WILL FORM PROTECTIVE SEAL WHEN COVER IS ASSEMBLED LIP ASSEMBLE ONE OF THESE LOW POINTS TOWARDS NARROW EDGE OF ELEMENT SCREW 104 86 68 50 32 14 -4 -22 °F 40 30 20 10 0 -10 -20 -30 °C SAE 30 10W-30 SYNTHETIC 5W-30 5W-30 12 COOLING SYSTEM (See Fig. 15) Your engine is air cooled. For proper en gine performance and long life keep your engine clean. • Remove blower housing and clean as nec es sary. • Keep cylinder fins free of dirt and chaff. Fig. 15 MUFFLER Do not operate tiller without muffler. Do not tamper with exhaust system. Damaged mufflers or spark arresters could create a fire hazard. Inspect pe ri odi cally and re place if nec es sary. If your engine is equipped with a spark arrester screen assembly, re move every 50 hours for cleaning and inspection. Re place if dam aged. SPARK PLUG Replace spark plugs at the beginning of each tilling sea son. Spark plug type and gap setting are shown in “PROD UCT SPEC I FI CA TIONS” on page 3 of this manual. TRANSMISSION Your transmission is sealed and will not re quire lubrication unless serviced. CLEANING Do not clean your tiller when the engine and transmission are hot. We do not rec om mend using pressurized water (gar den hose, etc.) to clean your unit un less the gasket area around the trans mis sion and the engine muf fler, air fil ter and car bu re tor are cov ered to keep wa ter out. Wa ter in en gine will short en the useful life of your tiller. • Clean engine, wheels, finish, etc. of all foreign matter. • Keep finished surfaces and wheels free of all gas o line, oil, etc. • Protect painted surfaces with au to mo tive type wax. MAINTENANCE COOLING FINS BLOWER HOUSING MUFFLER 13 TILLER Fig. 16 Fig. 17 Fig. 19 CAUTION: Disconnect spark plug wire from spark plug and place wire where it cannot come into contact with plug. TINE ARRANGEMENT Your outer tines can be assembled in several different ways to suit your tilling or cultivating needs. CAUTION: Tines are sharp. Wear gloves or other protection when han dling tines. tine_4 OUTER TINE HAIRPIN CLIP INNER TINE A B A B CLEVIS PIN MID-WIDTH TILLING - 22" PATH (See Fig. 17) • Assemble ho...
Эта инструкция также подходит к моделям:Культиваторы - 433691 (5.39 mb)
Культиваторы - 96083000300 (5.39 mb)