Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
You have following options to charge the i.roc x20: 2.1 Inside Dockingstation with assembled adaptor 2.2 Using direct connected charger 2.3 Using the USB connection set 3 3 Power On Press the Power button to turn the unit on. 4 4 Set up the device When the Windows Mobile screen displays on the screen tap anywhere on the screen and follow the on-screen instructions until setup is complete. 5 5 Insert the Companion CD into the computer Insert the Companion CD into the computer‘s CD Rom drive. Click “Start Here“. Follow the on-screen instructions. The setup wizard installs following: -Active Sync 4.x or higher -Microsoft Outlook (if necessary) -Other optional software applications 6 6 Connect the i.roc x20 Pocket PC to your computer when instructed by setup wizard on the computer Therefore connect the USB connection cable to a free USB port on your computer, insert the i.roc x20 into docking station or connect the USB cable to USB connection set. 7 7 Establish a partnership Follow the on-screen Active Sync instructions to establish a connection between you Pocket PC and your computer or select guest partnership. Use of HP original documents The ecom instruments i.roc x20 Pocket PC is based on the HP iPAQ hx2000 Pocket PC family. Therefore all related HP documents or Software updates can be used further on. All modifications regarding the hardware are descripted within these booklet as good as possible. The use of standard software is equal to the original HP devices. Resetting the unit Depending on the i.roc x20 operating system, different resets can be performed. All resets should be performed without connected and powered charger. Windows Mobile 2003 SE Performing a Soft-Reset A Soft-Reset stops all running applications, but does not erase any programs or saved data. Be sure to save any unsaved data with a running application before performing a Soft-Reset. - To perform a Soft-Reset press both reset buttons on the keypad - The Pocket PC restarts and displays the today screen Performing a Hard-Reset Perform a Hard-Reset only when you want to clear all user-installed settings, applications, and data from RAM, where data and applications you have loaded are stored. Also after the battery is completely discharged, the device will operate in the same way after Hard- Reset. All i.roc x20 are equipped with a so called AutoInstallation tool, you can reload predefined programs and settings automatically. -To perform a Hard-Reset press and hold down the F1 and F4 buttons - While holding down these buttons, press the reset buttons for about two seconds - When the Pocket PC screen begins to fade, release the F1 and F4 buttons first and then release the reset buttons. - The Pocket PC resets and powers on Note: If you simultaneously push and hold the Reset, F1 and F4 buttons for more than two seconds, the battery disconnects. To restart the device, either plug the device into the AC Adapter or press the reset buttons again. Windows Mobile 5 Performing a Soft-Reset A Soft-Reset stops all running applications, but does not erase any programs or saved data. Be sure to save any unsaved data with a running application before performing a Soft-Reset. - To perform a Soft-Reset press both reset buttons on the keypad - The Pocket PC restarts and displays the today screen Performing a Hard-Reset A Hard Reset stops all running applications, but does not erase any programs or saved data. Additional to a soft reset all hardware registers will be erased. -To perform a Hard-Reset press and hold down the F1 and F4 buttons - While holding down these buttons, press the reset buttons for about two seconds - When the Pocket PC screen begins to fade, release the F1 and F4 buttons first and then release the reset buttons. - The Pocket PC resets and powers on Note: If you simultaneously push and hold the Reset, F1 and F4 buttons for more than two seconds, the battery disconnects. To restart the device, either plug the device into the AC Adapter or press the reset buttons again. Performing a Clean-Reset A Clean Reset clears all user-installed settings, applications and data from the device. - To perform a Clean-Reset, press and hold F1, F3 and the power buttons - While holding down these buttons, press the reset buttons for about two seconds - When the Pocket PC restarts release first the F1, F3 and power buttons first and then release the reset buttons - The Pocket PC resets and powers on System Overview 1 2 3 4 5 6 7 8 10 11 12 13 14 9 Front and bottom panel components 1 Flat top panel, optional long top panels for adding barcode or RFID modules available 2 Wireless / Notification LED indicator Off = WiFi or Bluetooth are both off Blue flash = WiFi and / or Bluetooth are on Green flash = notification events have occured 3 Charge LED indicator Off = no charging Red flash = charging Red solid = charging complete 4 Touchscreen 5 Power button 6 F4 button (HP indication: iTask button) 7 F3 button (HP indication: Messaging button) Starting iPAQ Wire...