Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
There is no monthly fee to pay and your privacy is completely protected. With i.Trek TR-1, user can track any object globally in real time as long as the tracking object is within cell phone network and has line of sight with sky. Application Examples Vehicle Tracking – Locate important vehicles and assist in stolen vehicle recovery. Personal Tracking – Locate lost children or senior citizens. Requirements for using i.Trek TR-1: 1. A SIM card with a valid phone number associated for the tracker. 2. Any phone (home phone or mobile phone) for data communication. 3. A PDA, smart phone or laptop with Bluetooth capability and mapping software installed. How i.Trek TR-1 works 1. The user calls Tracker from any phone to establish a connection. 2. The Tracker receives signal from the satellite and encodes position data into voice data. 3. The encoded voice data travels through phone network as voice. 4. The phone receives the voice and passes to the decoder. 5. The decoder converts the voice back to position data and sends out via Bluetooth. 6. The display unit receives the position data and shows the tracker location on a map. (1) (2) (4) (3) (5) (6) Package Contents Tracker with Li-Ion battery Decoder with Secure Strap USB Charging Cable with USB Car Charger Manual and Tracking Software CD with serial number GPS/GSM Tracker GPS LED MMCX External Antenna Jack Power Button Alarm Release Button Battery LED Expansion Port GSM LED SOS Button Charging Port Power Button Press the power button to turn on / off the GPS tracker Battery LED Red – Battery low and requires charge Green – The battery is fully charged Orange – The battery is charging GSM LED Flashing Quickly – GSM stand-by Flashing Slowly – No SIM card or searching for network Solid – Network connected Charging port (mini1394) Connects to car charger or home charger to charge the battery GPS LED Flashing – The GPS is searching for satellites Solid – The GPS position has fixed SOS Button Press the button to report current position to pre-set phone numbers. Alarm Release Button (Applicable only with optional car control unit) Not used in default setting. When connecting to the optional car control unit, press the button to disable the alarm. External Antenna Jack (MMCX) Recommended if user plans to mount the GPS tracker inside the trunk or locations without direct view of the sky. Bluetooth Decoder (1) (2) (3) (4) (5) (6) (1) GPS LED Flashing orange – The GPS is searching for satellites Solid orange – The GPS position has fixed (2) Decoder LED Flashing red (4 sec. interval) – The decoder is decoding input data (3) Input LED Solid green – The decoder is receiving input data from phone (4) Bluetooth LED Flashing blue – Bluetooth not connected Solid blue – Bluetooth connected (5) Power / Output Switch Left – Decoder is off Middle – Decoder is on and the data is sent via wired connection (optional cable required) Right – The coder is on and the data is sent via Bluetooth connection (6) Built-in Microphone Built-in microphone to receive the voice input data from the phone Setting up GPS / GSM Tracker 1. SIM Card Installation SIM card slot is located inside the battery cabinet. Please open the battery cover underneath the tracker to locate SIM card slot. If the battery is already installed, please remove the battery to reveal the SIM card slot. Follow the figures below to install the SIM card. 2. Charging Battery It is recommended to charge the battery for overnight when you use the tracker for the very first time. When the power is full, the battery LED will turn green. With subsequent use, the battery will take about 3 – 4 hours to fully charge. Setting up GPS / GSM Tracker (Cont.) 3. Switch On Press the power button to switch on TR-1 tracker. Please make sure the GPS LED is flashing indicating it is getting a fix from the satellites. This may take 1 –2 minutes when you use the tracker for the first time. Also, the GSM LED also needs to be flashing indicating SIM card is inserted and GSM network is stand by. 4. Installation The high sensitivity of TR-1 tracker enables it to operate in challenging environments. TR1 tracker will work inside a vehicle, in glove box, under seats, or even inside the trunk. However, it is always recommended to install TR-1 in places with best view of the sky whenever possible. Green – Recommended Red – Not recommended ? – Experimentation required Tracking with Bluetooth Decoder 1. Establish connection between Tracker and Bluetooth Decoder From a telephone or mobile phone, dial the phone number of the SIM card inside the tracker. Connect your phone to the decoder by placing the decoder microphone on the phone speaker. The Bluetooth decoder will then convert the analog voice data back to real-time GPS digital NEMA messages. Please set power switch to the right position (Bluetooth) to use Blueooth connection. 2. Checking Decoder status Solid orange LED ( ) followed by blinking red LED ( ) means that the data is valid and you have a real time ...