Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
To make sure the ALCI is functioning properly, perform the following test. The purpose of this test is to allow you to make sure the exclusive water sensing system (ALCI) is working. 1) Plug in appliance and press test button on plug (see diagram below). 2) Appliance will stop working. There will be an audible click and a reset button will pop out. 3) To reset ALCI with the reset button, unit should be unplugged. Then push in reset button, and reinsert plug into outlet. 4) If ALCI is not functioning properly, return appliance to an authorized Conair service center. 5) It is important that if immersion of the transformer or the ALCI occurs, this unit be brought to a service center. Do not try to reset. Test Reset 6) Be sure to repeat test every time you use appliance to confirm ALCI is operational. Should the appliance go off and the ALCI reset button pop up during use, this could indicate a malfunction in the appliance. CAUTIONS • This unit should not be used in the following cases unless directed by a physician: Tuberculosis, benign and malignant tumors, hemorrhages, inflammations of the skin, phlebitis and thrombosis, open and fresh wounds, bruises, broken skin or varicose veins, or undetermined calf pain. • Consult your physician if you have any questions regarding the therapeutic use of this unit. • Do not use on any unexplained pain before consulting your physician. • Discontinue use of unit if pain increases or swelling occurs after application. • Do not use on any part of the body that is anesthetized. • Do not use on any part of the body where recent surgery was performed. • The recommended massage time is 15-20 minutes. • Consult your physician before use if you are pregnant. CAUTION MAT MAY MOVE WHEN YOU ENTER OR EXIT BATHTUB – EXERCISE CAUTION HOW TO USE BATH MAT AND MOTOR HOUSING 1) Remove bath mat, motor housing and air hose from packaging. Do not fill tub first. 2) Insert one end of the air hose into the female receptacle on one end of the mat. Press in firmly. 3) Before filling bathtub, place mat in tub with hose end toward the front of tub. Press mat firmly down to engage suction cups on bottom of mat. Suction cups may lose grip on textured surfaces or tubs with some dirt buildup. Clean area and moisten suction cups to increase suction cup grip. FOR TEXTURED TUB SURFACES: IF CUPS DO NOT ADHERE AFTER WETTING AND PRESSING FIRMLY, THEN PROCEED WITH CAUTION WHEN SITTING ON THE MAT. YOUR BODY WEIGHT WILL KEEP MAT POSITIONED DOWN IN TUB FOR USE. 4) Place motor housing on the floor conveniently between the bathtub and electrical outlet. Never place the motor housing where it can fall into the tub. Have the motor housing face the user in the tub, as the infrared remote control needs to be aimed by the user toward the motor housing. 5) Plug motor housing into 120 V AC outlet. See ALCI operating instructions to familiarize yourself with its ALCI and function. 6) Insert the other end of the air hose into the motor housing. 7) Press the remote’s On/Off button; motor will run on the low setting. Try other settings to become familiar with the unit's operation. (See “How To Use Remote Control.”) 8) Now fill the bathtub with the amount and temperature of bath water desired. Turn on unit to desired setting. 9) Exercise extra caution getting into and out of the bathtub. 10) The bath mat is designed to maintain the temperature of the water. However, as the overall temperature of water decreases, so will the bath mat’s ability to maintain the warm temperature. 11) Use of salts and oils is acceptable with your bath mat massager. Please clean the bath mat with fresh tap water before storing. Also note that your additions of salts or oil may make tub and bath mat surfaces slippery. 12) After use, be sure you are dry before unplugging power unit. 13) To store, drain all water from the bath mat sections by turning gently over in the bathtub. Disconnect the air hose from the power unit and drain air hose into tub as well. After all free water has dripped into the tub, gently wipe any wet surfaces with a clean dry towel before storing. 14) Dry the remote control after use. Avoid submerging or having control float on water for long periods of time. HOW TO USE REMOTE CONTROL 1) Find the remote control and carefully remove it from its wrapping. 2) Remove battery cover. Insert 2 AAA batteries (not included) following diagram engraved inside the battery enclosure. Carefully replace battery cover and make sure O ring is intact. 3) Your remote control has an On/Off button and a Mode button. 4) Aim the remote control at the top front of the motor housing. If the remote does not work, check that the batteries in the remote are fresh and making good contact. Press the On/ Off button, and the unit is on the low setting. By repeatedly pressing the mode button the speed goes to medium and then high. Press again and the setting goes back to low. HOW TO USE FOOT ROLLERS This model comes with foot rollers that can be used to massage ...