Оценок - 3, средний балл: 3.7
(
)
)
|
Фрагмент инструкции
This finest Whirlpool Pedicure Spa has been developed by J&A USA, Inc. to operate dependably for many years when used properly. Please take time to read this entire manual thoroughly before installation and use. PLEASE READ AND FOLLOW INSTRUCTIONS CAREFULLY! Important Precautions J&A USA requires that you contact your local, qualified electrician and plumber to install your PETRA Whirlpool Pedicure Spa. It cannot operate efficiently or safely unless it is provided with adequate electrical power, sufficient water pressure, proper water temperature and required drain facilities. Information on these important subjects contained in this manual. We urge you to read it carefully to make sure these requirements are met. Precautions 1 Excessive water temperature is dangerous and should be checked before use. Maximum water temperature should not exceed 100 deg. F. (38 deg. C.). 2 Always enter and exit the Whirlpool Pedicure Spa slowly and carefully. 3 Never bring and/or operate any electrical devices into or near the Whirlpool Pedicure Spa. 4 Do not stand in the whirlpool tub! 5 This Whirlpool Pedicure Spa has a weight capacity of 250lb. WARNING Do Not use if you are diabetic, have poor blood circulation, or if any area of your feet or legs are inflamed or have open wounds. Consult a physician before using if you have any kind of fungal infection, swelling, fracture, or persistent pain. Massage should be pleasant and comfortable. IF YOU EXPERIENCE PAIN OR DISCOMFORT, DISCONTINUE USE IMMEDIATELY AND CONSULT A PHYSICIAN. This product in whole is in compliance with the applicable UL LISTED standards and requirements for the US and Canada by Underwriters Laboratories Inc. Some of the components of this product are also in compliance with the applicable safety standards of the following: 3 Important Considerations Please read the following instructions thoroughly Inspection Please take time to inspect each pedicure spa shipment thoroughly for damages immediately upon delivery. If damages are found, it is very important to notify the freight driver and indicate extent of the damages on the bill of lading. If you fail to do so, J&A USA will not be responsible for the damages and may not be able to make appropriate claims to the freight carrier. Any damage claims must be filed directly by receiver to the freight carrier. Electrical Service Each Foot spa must have its own dedicated 115V, 60 Hz, 15 Amp GFCI protected grounded circuit. Water Supply Water supply to the PETRA pedicure spa should consist of a system that will provide both adequate water pressure and water temperature. All plumbing connections must conform to local codes. Water Pressure Normal water pressure of 30 to 120 P.S.I. is required to correctly fill the tub to the proper level. Back Flow Prevention Device - For following states: AZ, CA, IL, MN, NE, NV, OR, TX, WA, and WI; All PETRA pedicure spa are equipped with factory installed Dual Check Back Flow Preventer. Specification: Tested and certified to meet ANSI/ASSE standard 1024. CSA certified to standard No.B64.6 Pressure / Temperature Maximum pressure: 150 psi (10 bars) Minimum pressure: 10 psi (69kPa) Working temperature: 33F to 140F constant; intermittent to 180F (0.6C to 60C sustained; intermittent to 82.2C) Maximum recommended flow: 15 gpm (571pm) -For all other states: As an option, the Dual Check Back Flow Preventer will be factory installed. * Inquire with governing authorities for local installation requirements. Drain Facilities Connect the Foot spa drain to meet local plumbing codes. Please refer to the installation drawings on pages 9-10. Foot spa is recommended securely fastened to the floor Fasten the Foot spa with at least two fasteners. Installation Summary The installation must comply with local, state, and federal building, plumbing and electrical codes, where applicable. A licensed plumber should complete the plumbing of the pedicure spa. Note: Failure to comply with federal, state or local codes and ordinances will result in warranty being null and void. 4 PETRA 700& 500 IDENTIFYING PARTS 1 2 3 4 5 7 8 9 10 11 12 13 14 6 15 16 17 18 STOP CONTINUE/REPEAT THIGHMASSAGE AUTO TAPKNEAD UP DOWN MASSAGEWHEELS J&A A B FORWARD BACKWARD UP DOWN 19 20 SANIJET-Pipeless Standard Whirlpool Jet PARTS 1-PILLOW COVER 2-BACK REST 3-ARM REST 4-MATCHING ARM TRAY (OPTIONAL) 5-SEAT CUSHION 6-SHOWER SPRAYER 7-ADJUSTABLE FOOT CUSHION 8-ON/OFF WHIRLPOOL BUTTON 9-OPTIONAL ON/OFF BUTTON (LIGHT or DISCHARGE PUMP) 10-FAUCET 11-SANIJET PUMP IMPELLER 12-OVERFLOW WASTE KNOB 13-POP-UP DRAIN STOPPER 14-LIGHT COVER 15-BACK PANEL 16-ARM REST LEVER 17-BASE (SHELL) 18-WHIRLPOOL JET 19-MASSAGE REMOTE CONTROL 20-SLIDE/ RECLINE REMOTE CONTROL Due to continuous improvements on all our products; specifications, characteristics, packing, colors, designs are subject to change without notice 5 PETRA 450, 350R, 350V& 300 MASSAGE SYSTEM JA& PETRA 450 VIBRATION PETRA 300 Pacific spa J&A USA Inc. VIBRATION TRANSFORMER MODEL:GRA 1215 IN...