Оценок - 0, средний балл: 0
(
)
)
|
Фрагмент инструкции
The symbol disappears from the screen and the filter is operational again. Installing the double active filter: . Remove the basic filter from the appliance, Fig. 20. . Change the double active filter inside the basic filter for a new one as shown in Fig. 21. . Install the assembly onto the appliance by lining the lower studs up with the slots on the front casing of the appliance and pressing the top clip in until it clicks into position. The assembly is fitted properly when it clicks into position. . Close the front flap. Fig. 21 Double active filter . In order to maintain cooling power, only fit one set of filters onto the support. Note The flaps on these models are fitted with safety stops up to which point they can be opened without risk of the front flap falling and causing damage and/or injury. The flap on the appliance can be removed (firmly pull the flap towards you) to make it easier to clean and change the filters. Afterwards, or should for any reason the flap come out of its original housing, proceed as follows to fit it: 1° Lift the flap until it comes out of its lower supports, (Fig. 22: a). 2° Position the plastic leg in the front groove on the appliance (in T position) and slide it down to the safety stop, (Fig. 22: b). 3° fit the lower studs in the front stops on the appliance making sure that the plastic leg fitted in the previous step does not come out of position, (Fig. 22: c). When finished, the user should make sure that the flap is fitted properly and does not fall when opened again. (The door opens up to the safety stop). If not fitted properly, repeat steps 1° and 2° again. a b 45 Storage requirements When the appliance is out of use for a long period, set the expulsion tube to parking position so that the appliance takes up as little space as possible. . To do this, bend the tube towards the back of the appliance and secure it with the diffusion hook, Figs. 24 and 25. Prior to use at change of season . Clean the air filter. . Clean the casing and the grilles if necessary. Fig. 24 Fig. 25 Transportation requirements The appliance is fitted with wheels to make it easier to move around. It can be tilted, if necessary, in order to make transportation easier. You should not turn the appliance back on again for a minimum period of one hour after performing this procedure. . Before tilting it, empty the condensed water from the internal tank by extracting the water drainage pipe from its housing and removing the plug, Fig. 23. Place a receptacle (or the appliance’s removable tank) at the end of the water drainage pipe to collect the condensed water or lead the pipe to the nearest drain. Do not forget to replace the plug and reinsert the pipe in its housing when the tank is empty. Cleaning and Maintenance Fig. 23 Fig. 22 c Things to check before calling the Technical Service General requirements for operation What to do if ... ... the appliance does not work ... . Check that it is plugged in properly. . Check that the mains electricity supply is working. Check the fuse box. . Set the thermostat to a lower temperature. ... the appliance does not work and the symbol indicating that the condensed water tank is full is displayed on the screen ... . Set the appliance on a flat surface. If the symbol does not disappear, empty the water tank. Make sure that the tank is refitted properly afterwards. (See instructions in "Cooling"). ... the appliance does not reduce room temperature sufficiently ... . Check the joins on the hot air expulsion tube. . Make sure that the expulsion tube is not too bent and that it is not extended to more than 140 cm. . Make sure that the plug is fitted on the drainage water pipe. . Fit the suction pad to close the window as far as possible. . Lower blinds to reduce direct sunlight. ... the fault symbol is displayed on the screen ... . Get in touch with an authorised dealer, customer service or the manufacturer’s Technical Service Network. ... there is water on the control panel grille or on the basic filter housing ... . There is no cause for concern. This is normal. Noise ... the appliance makes a lot of noise ... . Some noise is normal and other types of noise can be solved easily. You need to be able to distinguish between these types of noise: Perfectly normal noise . The sound of water flowing in cycles is due to the pump, which circulates the water to enhance the power of the appliance. . A dull, humming sound is inevitable due to the compressor. . A faint, whistling sound is due to the refrigerant passing through the thinner pipes on the appliance when the compressor starts up. . A short clicking sound is produced when the pump connects and disconnects or when the regulator connects or disconnects the electronics system. Easy-to-solve noises . Make sure that the air expulsion tube and the diffusion and collection sleeves are fitted properly onto the appliance. . Make sure that the air intakes and outlets on the appliance are free of obstacles. . Make sure that th...
Эта инструкция также подходит к моделям:Кондиционеры - PA20001M/02 (6.97 mb)
Кондиционеры - PA20001M/03 (6.97 mb)