Оценок - 2, средний балл: 3
(
)
)
|
Фрагмент инструкции
Attach the shutters to the cabinet using (2) 1/4" screws on each side 6. Installation of Mounting Brackets and First Sealing Strip (Model 463AAC005BA) NOTE: Windows come in a variety of different styles Therefore, it may be necessary to modify or Improve your particular installation A Assemble the leveling screw bracket to the bracket assembly as shown in (Fig 9), using two 1/4” screws provided Install the leveling screws into each of the leveling screw brackets (This will require the use of an adjustable wrench) B Measure the inside window sill width and find the center line as shown in (Fig. 10) From this center line, measure 8 1/16" on each side and mark these points Align the V-slot in each bracket on these marks and mount to sill using (2) 3/4" screws provided per bracket Brackets should be perpendicular to the inside window sill See(Fig 11) Fig 7 Fig 8 Fig 9 Fig 10 Inside Window Sit 3/16' Maximum _____ ♦ Bracket Assembly Leveling Screw Fig 11 - 8 - Installation Instructions C Adjust the leveling screws until the bracket tilts no more than 3/16” downward to the outside Do not allow the bracket to slant inward as condensation could possibly drip on interior walls and floors See (Fig. 11) D. Cut the 1st foam sealing strip to fit the underside of the bottom window sash Remove the peel-off backing on the foam and attach it to the sash See (Fig 12) Fig 12 7 Installation of Mounting Brackets and First Sealing Strip (Model 463AAC008BA) NOTE- Windows come in a variety of different styles Therefore, it may be necessary to modify or improve your particular installation A Attach the bracket assembly to 90°angle support brackets (Fig 13) using (2) 1 1/2" bolts Two bolts per bracket Secure with the (2) 1/4” lock washers and (2) 1/4"nuts DO NOT immediately tighten these bolts as it may be necessary to adjust the depth of the bracket assembly, depending on the depth of your window sill See (Fig 14) Install the two leveling screws into the 90 support brackets Test the bracket assembly in the window before cabinet installation If the leveling screws are distanced too far away from the wail to provide stability, it may be necessary for you to shim this area with a solid piece 6f wood See (Fig 15) Fig 13 Fig 14 (If required) Frg 15 - 9 - Installation Instructions B Measure the inside window sill width and find the center as shown in (Fig 14) Measure 9 1/4" from the center line on each side and mark these points Align the V-slot in each bracket on these marks and mount the brackets to the sill using 3/4" screws provided. Brackets should be perpendicular to the inside window sill. See (Fig 14) C For proper condensation run-off it will be necessary to adjust the angle/pitch of the window brackets This is accomplished by adjusting the distance of the leveling screw on the outer wall The maximum angle/pitch should not exceed more than 3/16" See (Fig 16) D Cut the first foam sealing strip to fit the underside of the bottom window sash Remove the peel-off backing on the foam and attach it to this sash See (Fig 12) CAUTION A Fig 16 Use a solid piece of wood to provide stability This will be required when sills are extra deep See {Fig 15) — 10 — Installation Instructions 8. Installation of the cabinet (Model 463AAC005BA and 463AAC008BA) A Align one hole in the bottom of the cabinet with one hole in the bracket assembly. Secure the cabinet to the bracket using a 1/4" screw provided Repeat the same procedure on the opposite side of the cabinet See (Fig 17) 8. Ensure the 1" shaped mounting channel is positioned in front of the sash The "IX shaped channel on the bottom of the cabinet should be positioned in the track provided on the bracket assembly Pull the window down until it rests just behind the front of the "L” shaped mounting channel See (Fig. 18) C Check to make sure that the cabinet is slanted slightly downward on the outside if necessary, re-adjust support bracket as shown in (Fig 11) Fig 17 Fig 18 — 11 — Installation Instructions 9. Secure Shutters A Carefully slide the air conditioner back into the cabinet. (Please seek assistance for this procedure) Reinstall the slide-out-chassis security screws (removed earlier) on both sides of the cabinet See (Fig 19) Secure the top of the frames to the window sash with (2) 3/4” screws B Now, secure bottom frame of shutters using one shutter clamp and one 3/4” screw on each side(F/g 79). 10. Reinstalling Front Panel and Air Inlet Grille (Model 463AAC005BA): A Position the front panel on the cabinet starting at the top The front panel lock tabs must be inserted into the retaining slots in the cabinet Repeat this procedure on all sides B Secure the front grille to the cabinet using the Philips screws removed ear1ier(Fig 20) C Replace the air filter D Position air inlet grille on the cabinet and gently press on it 11. Reinstalling Front Panel Assembly (Model 463AAC008BA) A Position the front panel on the cabinet starting at th...
Эта инструкция также подходит к моделям:Кондиционеры - 463AAC005BA (547.63 kb)