Оценок - 4, средний балл: 4.5 ( )

Производитель: Heat Controller Размер: 904.14 kb Название файла: Язык инструкции:

When adjusting the Right-Left Louvers, it Move the Right-Left louvers to adjust air flow in the direction you prefer. is necessary to stop the Air-Conditioner first and make sure that it stops completely before adjusting the direction. Right-Left Louvers knob knob(three places) En-9 05M150_9315255020-01_En 9 2005.12.15, 10:56 SWING OPERATION Begin air conditioner operation before performing this procedure. Press the SWING button (Fig. 6 S). The SWING Display (Fig. 7 a) will light. In this mode, the Air Flow Direction Louvers will swing automatically to direct the air flow both up and down. Press the SWING button (Fig. 6 S) once again. The SWING Display (Fig. 7 a) will go out. Airflow direction will return to the setting before swing was begun. To select SWING Operation To stop SWING Operation About Swing Operation During cooling/Dry mode : Swings between 1 and 3. During fan mode : • Air flow Direction setting 1,2,3. Swings between 1 and 3. • Air flow Direction setting 4,5,6,7. Swings between 3 and 7. . The SWING operation may stop temporarily when the air conditioner’s fan is not operating, or when operating at very low speeds. MANUAL AUTO OPERATION Use the MANUAL AUTO operation in the event the Remote Control Unit is lost or otherwise unavailable. How To Use the Main Unit Controls Press the MANUAL AUTO button (Fig. 2 2) on the main unit control panel. To stop operation, press the MANUAL AUTO button (Fig. 2 2) once again. (Controls are located inside the Open Panel) When the air conditioner is operated with the controls on the Main Unit, it will operate under the same mode as the AUTO mode selected on the Re- mote Control Unit (see page 6). The fan speed selected will be “AUTO” and the thermostat setting will be standard.(76°F) En-10 05M150_9315255020-01_En 10 2005.12.15, 10:56 CLEANING AND CARE Before cleaning the air conditioner, be sure to turn it off and disconnect the Power. CAUTION! Be sure the Intake Grille (Fig. 1 9) is installed securely. When removing and replacing the air filters, be sure not to touch the heat exchanger, as personal injury may result. Cleaning the Intake Grille Cleaning the Air Filter 1. Remove the Intake Grille. 1 Place your fingers at both lower ends of the grille panel, and lift forward; if the grille seems to catch partway through its movement, continue lifting upward to remove. 2 Pull past the intermediate catch and open the Intake Grille wide so that it become horizontal. Intake Grille Intake Grille 1221Mounting shaft Knob 2. Clean with water. Remove dust with a vacuum cleaner; wipe the unit with warm water, then dry with a clean, soft cloth. 3. Replace the Intake Grille. 1 Pull the knobs all the way. 2 Hold the grille horizontal and set the left and right mounting shafts into the bearings at the top of the panel. 3 Press the place where the arrow on the diagram indicates and close the Intake Grille. Mounting shaft Intake Bearing Grille 12 Knob 1. Open the Intake Grille, and remove the air filter. Lift up the air filter’s handle, disconnect the two lower tabs, and pull out. Air filter handle Hooks (two places) 2. Remove dust with a vacuum cleaner or by washing. After washing, allow to dry thoroughly in a shaded place. 3. Replace the Air Filter and close the Intake Grille. 1 Align the sides of the air filter with the panel, and push in fully, making sure the two lower tabs are returned properly to their holes in the panel. Hooks (two places) 2 Close the Intake Grille. (For purposes of example, the illustration shows the unit without Intake Grille installed.) . Dust can be cleaned from the air filter either with a vacuum cleaner, or by washing the filter in a solution of mild detergent and warm water. If you wash the filter, be sure to allow it to dry thoroughly in a shady place before reinstalling. . If dirt is allowed to accumulate on the air filter, air flow will be reduced, lowering operating efficiency and increasing noise. . During periods of normal use, the Air Filters should be cleaned every two weeks. Mounting shaft Knob Intake Grille . When used for extended periods, the unit may accumulate dirt inside, reducing its performance. We recommend that the unit be inspected regularly, in addition to your own cleaning and care. For more information, consult authorized service personnel. . When cleaning the unit’s body, do not use water hotter than 104 °F, harsh abrasive cleansers, or volatile agents like benzene or thinner. Do not expose the unit body to liquid insecticides or hairsprays. . When shutting down the unit for one month or more, first allow the fan mode to operate continuously for about one-half day to allow internal parts to dry thoroughly. En-11 05M150_9315255020-01_En 11 2005.12.15, 10:56 CLEANING AND CARE Air Cleaning Filter Installation 1. Open the Intake Grille and remove the Air filters. Air Filter (Right & Left) 2. Install the Air cleaning filter set (set of 2). 1 Set the air cleaning filter into the air cleaning filter frame. Air cleaning filte...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: