Оценок - 4, средний балл: 3.8 ( )

Производитель: Carrier Размер: 375.05 kb Название файла: de57cea2-2286-46b8-a758-89d8ec1ba672.pdf Язык инструкции:

EMERGENCY/REMOTE Switch 2. Press the ON/OFF button on the remote controller to turn on the unit. The On LED will light on the indoor unit and “ON” will light in the remote display. To select the various modes and settings, read the following pages. EMERGENCY REMOTE THREE MINUTE COMPRESSOR DELAY • After turning the indoor unit on and setting it for air conditioner operation, the compressor (outdoor unit) will not come on for three minutes. This is a feature that will protect the compressor from damage due to quick start and stops. 9 DSB-122L/122LH(.... ) 01.8.17 5:27 PM ...1.. 0 HOW TO INSTALL BATTERIES To install the batteries, follow the procedures below: 1. Slide down the cover to access most of the remote buttons. Slide down further to access the battery compartment. 2. Insert two “AAA” size Alkaline batteries following the polarity diagram below. ON/OFF TIMER ENTER/ CANCEL TURBO/MILD +– +– BATTERY PRECAUTIONS The precautions below should be followed when using batteries in this device: 1. Use only the size and type of batteries specified. 2. Be sure to follow the correct polarity when installing the batteries as indicated in the battery compartment. Reversed batteries may cause damage to the device. 3. Do not mix different types of batteries together (e.g. Alkaline and Carbon-zinc) or old batteries with fresh ones. 4. If the device is not to be used for a long period of time, remove the batteries to prevent damage or injury from possible battery leakage. 5. Do not try to recharge batteries not intended to be recharged; they can overheat and rupture. (Follow battery manufacturer’s directions). CELSIUS TO FAHRENHEIT CONVERSION CHART CELSIUS FAHRENHEIT 18 64.4 19 66.2 20 68 21 69.8 22 71.6 23 73.4 24 75.2 25 77 CELSIUS FAHRENHEIT 26 78.8 27 80.6 28 82.4 29 84.2 30 86 31 87.8 32 89.6 NOTES: • When operating the remote controller, make sure there are no obstructions between the remote controller and the remote sensor. • After a while the display goes blank to conserve battery power. To check the settings, press the ON/OFF button once. 10 DSB-122L/122LH(.... ) 01.8.17 5:27 PM ...1.. 1 TO SET AUTO MODE This unit will automatically operate the unit according to its surroundings while in the Auto mode. All you have to set is the desired temperature and it will control the fan, coolness and dehumidifier. Follow procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON”will light in the remote display. 2. Make sure the AUTO indicator appears in the remote display. Using the TEMP. Ў or ^ buttons, set the desired temperature. The desired temperature can be changed up or down 1 degree from the actual room temperature. For temperature setting: 24~28°C AUTO 3. Then the unit will automatically operate. AUTO TO SET QUICK MODE To set this unit to cool at the highest power, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light on the indoor unit and “ON” will light in the remote display. 2. Press the MODE button until the Quick indicator appears in the display. 3. The unit will then start cooling the room at the highest power. TO SET COOL MODE To set the unit to cool the room to a desired temperature, follow the procedures below: 1. Press the ON/OFF button on the remote control to turn the unit on; the On LED will light ...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: