Оценок - 1, средний балл: 4
(
)
)
|
Фрагмент инструкции
♦ The air conditioner starts up in the Cool mode. You can change modes at any time. To adjust the temperature, press the /'''■»Nor buttons on the remote control or unit one or more times until the desired temperature is displayed. The temperature can be set between 18°C and 30°C. Result: ♦ Each time you press the | a |or | v | buttons: - The temperature is adjusted by 1°C and displayed on the control panel - The unit beeps ♦ The air conditioner starts cooling, if the room temperature is higher than the selected temperature. ♦ If the room temperature reaches the set temperature, the air conditioner stops cooling, but the fan is still operating. To set the fan speed: ♦ Press the £ F3 l.c'' fî; or ♦ Press the FÏJ button on the remote control as desired. s-1 button on the unit one or more times until the desired Fan speed(F1, F2 or F3) is displayed. 5 To control the direction of the air flow, refer to page 11. 4e~S) Airing Your Room If you want to provide air circulation without cooling, you can use the Fan mode. 1 If necessary, press theO (On/Off) button. Result: ♦ The air conditioner starts up in the Cool mode. ♦ The unit beeps twice. Remote Control Control Panel If the fan speed(F1, F2 or F3) is not displayed on the control panel: ♦ Press the ^ & ) button on the remote control or ♦ Press the I jBfr I button on the unit one or more times until the fan speed (F1, F2 or F3) is displayed. Result: ♦ The unit beeps each time you press the (, # 1 /1 jSBri button. ♦ The air conditioner starts up in Fan mode. You can change modes at any time. When the air conditioner is in the Fan mode, the temperature cannot be set or displayed. To set the fan speed ♦ Press the or ♦ Press the P orOT button on the remote control as desired. button on the unit one or more times until the desired fan speed(F1, F2 or F3) is displayed. 4 To control the direction of the air flow, refer to page 11. ENGLISH Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. Remote Control Control Panel 1 If necessary, press the (I) (On/Off) button. Result: ♦ The air conditioner starts up in the Cool mode. ♦ The unit beeps. Ifff“ The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: ♦ Plugged in ♦ Stopped It will start up normally after three minutes. 2 If the E3 is not displayed at the top of the control panel, press the l~^~l button on the control panel one or more times until it appears. Result: ♦ The unit beeps each time you press the HM~l button. ♦ The air conditioner runs in Dry mode. You can change modes at any time. 3 To adjust the temperature, press the I a i or I v I buttons one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C inclusive. Result: ♦ Each time you press the or (~~v~| buttons: - The temperature is adjusted by 1°C - The unit beeps ♦ The air conditioner starts removing the excess humidity; the quantity of air is adjusted automatically. 4 To control the direction of the air flow, refer to page 11. Adjusting the Air Flow Direction Horizontally Depending on the position of the unit in your room, you can adjust the orientation of the inner air flow blades on the unit. Adjust the air flow blades to the desired position by pushing them side to side. ENGLISH Setting the On Timer Remote Control Control Panel The On Timer enables you to switch on the air conditioner automatically after a given time. You can select the On timer only when the air conditioner is off. You can select the On timer when the air conditioner operates in the Cool or Dry mode. 1 Check that the air conditioner has been switched off; if necessary, press the (!) (On/Off) button. Set the operating time by pressing the fffl) button on the remote control or I a I button on the unit one or more times until the desired time is displayed. The operating time can be set between 1 and 24 hours. Result: ♦ Each time you press the I ¡3) I button: - The time is adjusted by 1 hour and displayed on the control panel - The unit beeps ♦ The operating time is displayed and decreases automatically to indicate the remaining time. ♦ The air conditioner starts up in the Cool or Dry mode automatically when the operating time reaches zero. You can select the fan speed, temperature and Energy saving mode after setting the On timer and Off timer mode. However, when you change the mode, the On timer and Off timer mode is canceled. To Cancel the On Timer To cancel the timer, press: ♦ Timer on the remote control or unit one or more times untilis displayed, or The (!) (On/Off) button on the remote control or unit (The air conditioner operates in the mode selected when the unit was last used.) e-12 Setting the Off Timer The Off Timer enables you to switch off the air conditioner ...