Оценок - 2, средний балл: 3 ( )

Производитель: Danby Размер: 1.99 mb Название файла: d72a9e6c-75a1-4e75-8c04-816df8bcc6a1.pdf Язык инструкции:

To change the temperature scale displayed on the electronic display, press both the “Temp/Timer” adjust arrows simultaneously to alternate between “Celsius” & “Fahrenheit”. CHECK FILTER : The adjacent indicator light will illuminate as a reminder to clean the air conditioner filter (see page 9) Once the filter has been cleaned and replaced, depress the Check Filter button in order to resume operation. SLEEP MODE : When activated, the current set temperature is gradually increased over a one (1) hour period then maintained for seven (7) hours. Once the program is complete, the air conditioner will resume to it’s previous set temperature (before sleep mode was activated). This feature is meant to be used during the night time hours to prevent the room from getting too cold (while you sleep) and results in less compressor running time and reduced energy consumption. Sleep mode may be cancelled by depressing the Sleep Mode button while the program is running. Mode Selector Temp/Timer Control MODE Auto Auto Fan Speed Power ButtonEnergy Saver Sleep ModeCheck Filter Auto Timer LED DISPLAY 68 AUTO-TIMER: Used to Initiate the Auto On and/or Auto Off timer. While the Air Conditioner is off (Auto-On): 1. Press the Auto-Timer button once and the adjacent Auto-On indicator light ‘ ‘ will illuminate. 2. Use the Temp/Timer control cursors to select a delayed Ontime of up to 24 hours. 3. Select the appropriate mode under which you want the unit to operate (Auto-Cool-Dry-Fan Only) 4. Select the fan speed setting. 5. The time you selected will appear in the LED display.. While the Air Conditioner is on (Auto-Off); 1. Press the Auto-Timer button twice and the adjacent Auto-Off indicator light will illuminate. 2. Use the Temp/Timer control cursors to select a delayed Offtime of up to 24 hours. 3. The time you selected will appear in the LED display The Auto On and Auto Off timer can operate during the same program by defining the Auto-Off parameters immediately after the Auto On parameters. The Auto-Timer may be cancelled at any time by turning the unit On/Off. 7 Remote Control Features Electronic Display: Displays the following information; A: Remote Control power On/Off and Mode Icons B: Clock and Auto-Timer settings C: Current set temperature D: Fan speed setting Control Buttons 1. Power switch. 2. Mode 3. Fan Speed 4. Energy Saver 5. Auto-Timer 6. Used to increase or decrease temperature settings in 1° increments on the Celsius or Fahrenheit scale. 7. Cancels current Timer ON/OFF settings. 8. Lock prevents the remote control settings from inadvertently being changed. 9. Clock: Depress the button for 3 seconds in order to set the clock. Press the increase or decrease arrow to adjust the clock in 1 minute intervals, holding down the increase or decrease arrow will adjust the time in 10 minute intervals. 10. Used to activate the SLEEP program. 11. Toggle the LED backlight on/off. 12. Restore remote control default settings. To operate the hand held remote control will require two “AAA” Alkaline batteries (included ). Batteries should be replaced when: a) No signal (beep) is heard when attempting to program the main unit. b) The main unit does not respond to a command issued by the remote control. Battery replacement: 1. Slide the rear cover on the remote in the direction of the arrow. Continue pulling (gently) until the cover separates completely from the unit. 2. Insert (2) batteries (AAA) following the same orientation (polarity) depicted inside the battery chamber.(+/-) 3. Re-install rear cover. 4. If the remote control will not be used for extended periods of time (vacations etc.), batteries should be removed. The remote operates within a range of 8 meters (26 ft.) from the receiver located inside the main unit. Any obstruction between the receiver and remote may cause signal interference, limiting the ability to program the main unit. 8 M ODE © 1 2 3 4 5 6 7 8 9 10 11 A B C D Electronic Display 12 Care and Maintenance Care and Maintenance End-of-Season Care 1. Operate the fan alone for half a day to dry out the When cleaning the air conditioner, be sure to inside of the unit. turn the POWER OFF and disconnect the power 2. Turn off power and remove plug from wall socket. cord from the electrical outlet. 1. DO NOT use gasoline, benzine, thinner or other chemicals on the air conditioner as these substances may cause damage to the paint finish and deformation of plastic parts. 2. Never attempt to pour water directly on unit as this will cause deterioration of the electrical insulation. Air Filter Removal: The air filter is located behind the air intake front grill. To remove the air filter, grasp the sides of the front grill and pull forward to open and ac...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: