Оценок - , средний балл:
(
)
)
Производитель: Frigidaire
Размер: 1.18 mb
Название файла: c5233e7e-8422-4b4c-82b9-592a1c18c5f3.pdf
Язык инструкции:
Документ загружается, подождите пожалуйста
 |
Документ загружается, подождите пожалуйста
Фрагмент инструкции
. If the window is a triple-track type with a screen panel included, remove the screen completely before installation. • Be sure the air conditioner has been securely and correctly installed according to the separate installation instructions provided with this manual. Save this manual and the installation instructions for possible future use in removing or reinstalling this unit. • When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils. Electrical Information The complete electrical rating of your new room air conditioner is stated on the serial plate. Refer to the rating when checking the electrical requirements. • Be sure the air conditioner is properly grounded. To minimize shock and fire hazards, proper grounding is important. The power cord is equipped with a three-prong grounding plug for protection against shock hazards. •Your air conditioner must be used in a properly grounded wall receptacle. If the wall receptacle you intend to use is not adequately grounded or protected by a time delay fuse or circuit breaker, have a qualified electrician install the proper receptacle. • Do not run air conditioner with outside protective cover in place. This could result in mechanical damage within the air conditioner. • Do not use an extension cord or an adapter plug. READ THIS SECTION BEFORE ATTEMPTING TO OPERATE AIR CONDITIONER. Operation of Current Device Plug in & press RESET The power supply cord contains a current device that senses damage to the power cord. To test your power supply cord do the following: 1. Plug in the Air Conditioner. 2. The power supply cord will have TWO buttons on the plug head. Press the TEST button. You will notice a click as the RESET button pops out. 3. Press the RESET button. Again you will notice a click as the button engages. 4. The power supply cord is now supplying electricity to the unit. (On some products this is also indicated by a light on the plug head). NOTES: • Do not use this device to turn the unit on or off. • Always make sure the RESET button is pushed in for correct operation. • The power supply cord must be replaced if it fails to reset when either the TEST button is pushed, or it cannot be reset. A new one can be obtained from the product manufacturer. • If power supply cord is damaged, it CANNOT be repaired. It MUST be replaced by one obtained from the product manufacturer. 4 SZ000710(En)-JiXie 4 2005.9.13, 11:04 AM To begin operating the air conditioner, follow these steps: Using Air Conditioner 1. Set the thermostat to the highest number (coldest or cooler setting). 2. Set the selector control to the highest COOL setting. NOTE: If the air conditioner is turned off, wait 3 minutes before restarting. This allows pressure inside the compressor and equalize. Failure to follow these instructions may be harmful to your unit. Air Conditioner Features 3. Adjust the louvers for comfortable air flow (see Air Directional Louvers). 4. Once the room has cooled, adjust the thermostat to the setting you find most comfortable. Review the “Air Conditioner Features” section for other settings. The controls featured in this manual are representative of many available models. Your model may offer slightly different features. Cool Mode The desired cool setting is selected by rotating the knob to the right to the appropriate location. “hi cool” has maximum cooling effect and airflow. “lo cool” has minimum cooling effect and airflow. Note: If your unit is equipped with a vent handle, keep it closed for maximum efficiency. Fan Mode Rotate the knob to the left to select your choice of fan speeds for air circulation. Note: When selecting a fan speed, the compressor will not run. Thermostat The thermostat is used to set the desired room temperature when the unit is being operated in the “COOL MODE”. To set the desired room temperature, rotate the thermostat switch to the desired setting. After the set temperature is achieved the thermostat will automatically start and stop the compressor in order to maintain the desired set temperature. Rotate the thermostat selector clockwise for higher cool settings. Higher cool settings will provide lower room temperature. Rotate the thermostat selector counter clockwise for lower cool settings. Lower cool settings will provide higher room temperature. Please always wait 3 minutes when turning unit off then on again, and when changing from cool to fan & back to cool. This prevents compressor from overheating & possible circuit breaker tripping. (2-WAY) AUGER WHEEL Air Directional Louvers Air directional louvers control air flow direction. Your air conditioner has the louver type described below. Auger Type Rotate the Auger Wheels until the desired Left/Right direction is obtained. 5 SZ000710(En)-JiXie 5 2005.9.13, 11:04 AM Care and Cleaning Clean your air conditioner occasionally to keep it looking new. Be sure to unplug the unit before cleaning to prevent shock or fire hazards. Air Filter Cleanin...