Оценок - 3, средний балл: 4
(
)
)
|
Фрагмент инструкции
Once the ambient temperature has reached the set temperature, the compressor will stop and unit will run in Fan mode. To conserve energy, the compressor will not start immediately after a couple degrees increase or decrease, but will wait for a 5°F allowance. For example: In Cooling Mode with a set temperature of 70°F When compressor first stops after reaching 70°F, unit will auto-switch to Fan. Compressor will start cooling again when ambient temperature increases to 75°F or above. In Heating Mode with a set temperature of 72°F When compressor first stops after reaching 72°F, unit will auto-switch to Fan. Compressor will start heating again when ambient temperature drops to 67°F or below. In Auto Mode (with preset temperature of 68°F for heat and 75°F for cool) Compressor will start cooling again when ambient temperature reaches above 80°F or will start heating when ambient temperature drops below 63°F. 8 Parts Front Back 1. Control Panel 2. Cooling Air Outlet 3. Handle 4. Castors 6. Air Inlet 7. Exhaust Air Outlet 8. Cord Hanger 9. Water Stopper (Rubber Plug Inside) Accessories 10. Adaptor - for insertion over the hose and into the back of the air conditioner I I. Exhaust Hose 12. Adjustable Slide Bar I 3. Round Connector 14. Cap for Round Connector 15. Remote Control (Electronic control models only) 5 Installation In order for this unit to function properly, it must be vented to the outside. Fitting the Exhaust Hose through the window is easy. Please see below. I. Extend Hose at least 6" and insert it into back of the unit, tightening into place by turning it clockwise. 2. Attach Slide Bar Connector, (Round Connector) to the other end of the Hose by extending hose at least 6". Then tighten Hose by turning the (Round Connector) clockwise. 3. Place Adjustable Slide Bar in the window and expand so it fits tightly. 4. Lower the window 5. Make sure the Hose has no kinks. Slide Bar has 3 sections which allows installation in windows up to 48" in width. Wall 1. Make a hole (5.1" in diameter) in the wall. 2. Insert the Round Connector (part #13) into the hole and hold in place by using 4 small screws (not supplied). 3. Extend one end of the Exhaust Pipe (part #1 I) and screw into the Round Connector by turning clockwise. 4. Extend other end of exhaust pipe and screw in Adaptor (part #10) by turning clockwise. 5. Push Adaptor to fit firmly over the opening on the back of the unit. **When not in use, cover the Round Connector and hole with Cap (part # 14). Connection Round Connector 6 Installation Mounting the Exhaust Pipe • The supplied Exhaust Hose can be extended from I foot to 5 feet for mounting. It is recommended that you use the shortest possible length of Hose. Take care to prevent any kink or bend in the middle of the Exhaust Hose, as this will trap hot exhaust air, which will radiate back into the room. WARNING! The length of the Exhaust Pipe is specially designed according to the specification of this product. Do not replace or extend it with your own hose as this could cause the unit to malfunction. Cleaning the Filter Use a vacuum cleaner or tap the filter lightly to remove loose dust and dirt from the filters and then rinse them thoroughly under running water (no hotter than 104°F) Dry thoroughly before replacing. Notice! Never operate the unit without the filters. 7 Before Use Important! • Leave the unit in an upright position for at least 2 hours before use. • Always place the unit on an even surface. • The power cord has a built-in L.C.D.I. (Leakage, Current, Detection, Interruption) circuit breaker for added safety. If the power supply is interrupted, please press the reset button to reconnect the unit to the power source. The green light should be on. • Make sure the unit is connected to a correctly grounded power supply. • For proper operation, the unit must be vented to the outside. • Do not cover or obstruct the appliance inlet or outlet grilles. • To avoid the risk of shock, the product should never be used in bathrooms,shower rooms or in any other steamy or wet areas. • Always transport the unit in an upright position. • Do not sit or stand on the unit. • Do not place objects on the unit. • Do not touch the unit with wet/damp hands or when standing barefoot. • Drainage of the water container is required before moving the unit or putting it into storage. • If the electric socket is different from the plug provided, have a professionally qualified electrician replace the outlet with a suitable one. Avoid the use of adaptor plugs, multiple sockets and/or extension cords; if their use is necessary, ensure that they conform to the current safety regulations. • Do not pull the power cord or place it near a source of heat; always unroll it completely to avoid the possibility of dangerous overheating. • If the power cord is damaged, it must be replaced by a qualified person. THE MANUFACTURER DISCLAIMS ANY RESPONSIBILITY I...
Эта инструкция также подходит к моделям:Кондиционеры - 000E (1.78 mb)