Оценок - 4, средний балл: 4 ( )

Производитель: GE Monogram Размер: 1.94 mb Название файла: Язык инструкции:

The single unit in 50° 40° the “Incorrect” illustration below obviously cannot condition the entire room. Add a second unit as shown in the “Correct” illustration. INCORRECT CORRECT OVER 40 FT. OVER 40 FT. ge.com Dimensions RAB71A WALL CASE WALL OPENING 16-1/4" MIN. x 42-1/4" MIN. 42" 133/ 4" 16" 1-1/2" TYP 1/2" 6" 21" 36" A 1/2" SQ. HOLE (2 REQ'D.) 1/2" DIA. HOLE (3 REQ'D.) 2-3/4" 5-5/8" 4" Additional Wall Case Depths RAB7116 - 16" RAB7124 - 24" RAB7128 - 28" RAB71 1 - 1" RAB77 WALL CASE WALL OPENING 16-1/2" MIN. x 42- /8" MIN. 6" 19" 36" 16-1/4" 13-7/8" 1-1/2" 42-1/8" 1/2" SQ. HOLE (2 REQ'D.) 9/16" 2-7/8" 5-5/8" 4" 1/2" DIA. (3 REQ'D.) RAB71 = 42" RAB71 = 20-7/8" GRILLE RAB77 = 42-1/8" RAB77 = 21" WALL CASE WITH GRILLE CHASSIS INSTALLED WALL CASE WITH SUB-BASE 3-1/2" KNOCKOUTS (ENCLOSURE) LEVELING SCREW 4 REAR; 4 BOTTOM SEE PAGE 32 FOR KNOCKOUT LOCATION DIMENSIONS. RAB71 = 13-3/4" RAB77 = 13-7/8" 42" TOP VIEW ROOM CABINET ROOM INSIDE CABINET SIDE VIEW OUTSIDE RAB71 = 16" RAB77 = 16-1/4" 7-1/8" FRONT VIEW* 12-3/4" 12" 9-3/8" 2-1/2" 1-7/16" 1-5/16" 2-3/8" MIN. INTERIOR WALL 3" MIN. ADJUSTABLE TO 5" MAX. SIDE VIEW 13" FINISHED FLOOR *SHOWN WITH ACCESS COVERS REMOVED. NOTE: CAUTION -REMOVE KNOCKOUTS FROM INSIDE OUT. Installation Instructions Packed With Wall Case . . . See Page 25 For Additional Information Concerning Outdoor Weather Panel and Case Stiffener. Wall Case A choice of wall cases is available for the Zoneline.® RAB71A — This insulated case is constructed of heavy-gauge galvanized steel and finished with a protective baked-enamel finish for protection and appearance. Design of the case provides for support of the chassis and free draining of any water entering the wall case. A petroleum microcrystalline wax is applied at critical points of fabrication to seal against moisture. The dimensions of the RAB71 wall case are: 42" wide by 16" high by 1 - /4" deep, the same dimensions as the original wall case for GE Zonelines built in 1961. The RAB71 wall case is also available in depths other than the standard depth. It is available on special order as: RAB7116 – 16" deep; RAB7124 – 24" deep; RAB7128 – 28" deep; and RAB7131 – 31" deep. All of these special-order deep wall cases are insulated and have sheet metal dividers, or splitters, to prevent the recirculation of condenser discharge air. RAB77 — This non-insulated wall case is molded from fiberglass-reinforced polyester compound. This SMC (Sheet-Molded Compound) wall case offers outstanding strength, durability, color retention, water integrity and corrosion resistance. The dimensions of the RAB77 wall case are: 42-1/8" wide by 16-1/4" high by 1 -7/8" deep. • Both wall cases are of universal design, accepting all Zoneline chassis of current design as well as all GE Zoneline chassis produced since 1961. • Drain holes are provided in the rear of the wall case to permit excessive cooling condensate water, heat pump condensate or precipitation entering the wall case to drain freely. A drain kit may be connected to the wall case to control any water draining from the wall case. See page 5 for information on RAD10 Drain Kit. RAK901L — For installations where the wall case extends into room, RAK901L is an insulation kit that can be used with the RAB77 or any existing non-insulated wall case to minimize the possibility of condensation forming on the indoor side of the case during the winter. Sub-Base The sub-base is an optional accessory for the Zoneline and is presented with the wall case information since the decision to use or not to use a sub-base in the installation is a factor in the location of the wall opening for the unit. National Electrical Code® requires that air conditioning units connected to voltages in excess of 250 volts be “permanently connected.” There are also some installations where units connected to voltage sources under 250 volts may also need to be “permanently connected.” If you are in doubt about the requirements for a particular installation, consult Article 440 of the NEC or the local electrical inspector. These requirements are designed to protect personal safety and should be strictly followed. Although NEC is cited here as a reference, all electrical wiring and installations must conform to any and all local electrical codes and regulations. “Permanent Connection” generally means wiring to the unit must be contained in an enclosed “chaseway,” where access to the wiring connections is more restrictive than a normal line cord plugged into a receptacle. NEC requirements may be met by using flexible or rigid conduit to contain the wiring between the unit and a junction box that contains the wiring connections. The conduit is connected to the unit and to the junction box with connectors to hold the conduit in place. The junction box may be located in the floor or the wall of the structure but only approved connectors may be used outside the unit or the junction box. The sub-base is UL® listed as a junction box for permanent connect...

Скачать инструкцию

Чтобы скачать, введите 2 цифры: