Оценок - 4, средний балл: 4.3
(
)
)
|
Фрагмент инструкции
Setting Mode • Press 2 to select:Cooling Model AUTO – Automatic Operation COOL – Cooling Operation DRY – Soft Dry Operation FAN – Air Circulation Operation Heat Pump Model AUTO – Automatic Operation HEAT – Heating Operation COOL – Cooling Operation DRY – Soft Dry Operation Operation Standard temperature Indoor temperature 23°C 20°C Heat Pump Model COOL –> 26°C ~ 28°C DRY –> 1°C ~ 2°C lower than the room temperature HEAT –> 20°C ~ 24°C Cooling Model COOL –> 26°C ~ 28°C DRY –> 1°C ~ 2°C lower than the room temperature TEMP AUTAUTOFANAN AUTAUTO RESETCLOCK OFF CANCEL 1 2 TIMER OFF/ ONAUTO MANUAL QUIET POWERFULON SE FAN SPEED MODE 235164PREPARATION BEFORE OPERATION Indoor Unit 1 Connect the power supply cord to an independent power supply 2 Open the front panel 3 Remove the air filters 4 Fit the air purifying filters in place 5 Insert the air filters 6 Close the front panel Remote Control – To set the current time 1 Press 1. 2 Then press 2to increase or decrease the time. 3 Press 1 again. Set time at display will light up. CHECK RESET CLOCK FAN SPEED AIR SWING OFF CANCEL ON SET 1 2 3 TIMER AUTO MANUAL 126 2 1 45 3 Setting Temperature • Press 3to increase or decrease the temperature. • The temperature can be set between 16°C ~ 30°C. • Recommended temperature: • During AUTO Operation, press 3 to select:• Operation with 2°C higher than the standard temperature. • Operation with the standard temperature. • Operation with 2°C lower than the standard temperature. Standard Temperature Cooling Model • Once the Automatic Operation is selected, the indoor temperature sensor operates automatically to select the desired operation mode with Cooling or Soft Dry. • After the operation mode has been selected, the mode does not change. Heat Pump Model • At the beginning of the automatic operation, Heating, Cooling or Soft Dry is automatically selected according to the indoor temperature. • The operation mode changes every hour, when necessary. Operation Standard temperature Indoor temperature 23°C HOW TO OPERATE To start the operation • Press 1. • POWER indicator (green) on the indoor unit will light up. • To stop, press once more. Setting Mode • Press 2 to select:Cooling Model AUTO – Automatic Operation COOL – Cooling Operation DRY – Soft Dry Operation FAN – Air Circulation Operation Heat Pump Model AUTO – Automatic Operation HEAT – Heating Operation COOL – Cooling Operation DRY – Soft Dry Operation Operation Standard temperature Indoor temperature 23°C 20°C Heat Pump Model COOL –> 26°C ~ 28°C DRY –> 1°C ~ 2°C lower than the room temperature HEAT –> 20°C ~ 24°C Cooling Model COOL –> 26°C ~ 28°C DRY –> 1°C ~ 2°C lower than the room temperature TEMP AUTAUTOFANAN AUTAUTO RESETCLOCK OFF CANCEL 1 2 TIMER OFF/ ONAUTO MANUAL QUIET POWERFULON SE FAN SPEED MODE 235164 CS-A7CKP CU-A7CKP5 / CS-A9CKP CU-A9CKP5 / CS-A12CKP CU-A12CKP5 NAME OF EACH PART Remote Control Remote Control Signal. • Make sure it is not obstructed. • Maximum distance : 10 m. • Signal received sound. One short beep or one long beep. Notes for Remote Control. • Do not throw or drop. • Do not get it wet. • Certain type of fluorescent lamps may affect signal reception. Consult your dealer. CHECK TEMP AUTO ON OFF AUTAUTO DRDRYFANANCOOLCOOL FAN AUTO RESET CLOCK MODE POWERFULQUIET FAN SPEED AIR SWING OFF CANCEL ON SET 1 2 3 TIMER OFF/ON AUTO MANUAL # ! $ % ^ $ * & 35879064( 21HEAHEAT How to Insert the Batteries 1 Slide down the remote control cover completely 2 Insert the batteries – Be sure the direction is correct – 12.00 at display - flashing • Set the current time (CLOCK) immediately to prevent battery exhaustion. About the batteries • Can be used for approximately one year. Observe the following when replacing the batteries • Replace with new batteries of the same type. • Do not use rechargeable batteries (Ni-Cd). • Remove the batteries if the unit is not going to be used for a long period. 1Signal Transmitter 2Operation Display 3Ionizer Mode Operation Button 4Room Temperature Setting Button (illuminating button) 5Operation Mode Selection Button 6Quiet Mode Operation Button 7Auto Airflow Direction Button 8ON-Timer Button 9OFF-Timer Button 0Reset Point (Press with fine-tipped object to clear the memory) !OFF/ON Button (illuminating button) @Powerful Mode Operation Button #Fan Speed Selection Button $Manual Airflow Direction Selection Button %Timer Set Button ^Timer Cancellation Button &Time-Setting Button *Clock Button (Remote Control Cover CLOCK OFF CANCEL 1 2 TIMER EON SE 2 1 1.5V1.5V Cooling 25°C Soft Dry 22°C Cooling 25°C Soft Dry 22°C Heating 21°C 40 CS-A7CKP CU-A7CKP5 / CS-A9CKP CU-A9CKP5 / CS-A12CKP CU-A12CKP5 MANUAL Five stages of adjustment can be made between 14° ~ 36°. MANUAL Five stages of adjustment can be made between 0° ~ 61°. Heat Pump Model MANUAL Five stages of adjustment can be made between 14° ~ 36°. Swing up/down Automatically Move up/down Automatically MANUAL Five stages of adjustment can be made between 0° ~ 61°. – When the discharge air temperatu...
Эта инструкция также подходит к моделям:Кондиционеры - CS-A9CKP (402.75 kb)
Кондиционеры - CS-A7CKP (402.75 kb)