Оценок - 4, средний балл: 3.8
(
)
)
|
Фрагмент инструкции
Choose Cooling Only Remote controller or Heat Pump Please refer to page 1 " Preparation before use" for details. Back-light Function (optional) Remote controller holder Signal receptor Remote controller Please refer to page 1 "Preparation before use" for details. Remote controller If the replacement is done within 1 minute, the remote controller will keep original presetting. However, if you want to change the presetting fromHeat Pump to Cool Only or Cool Only to Heat Pump, you should reload batteries 3 minutes after removing the old ones. (Please refer to page 1 for details.) PDF created with pdfFactory Pro trial version Operation instructions SMART SLEEP SUPER Each time button is pressed, the operation mode is changed in sequence: MODE Each time the "FAN" button is pressed, the fan speed is changed in sequence: 18 ~32 Heating mode is NOT available for cooling only air conditioner. HEATING COOLING DRY FAN ONLY Selecting mode FAN mode 2+- Auto High Medium Low At "FAN ONLY" mode, only "High","Medium" and "Low" are available. At "DRY" mode, airflow is set at "Low" automatically, "FAN" buttonis ineffective in this case. Setting temperature Press once to temperature setting by1lower . Press once to temperature setting by1raise . Range of available set temperature *HEATING, COOLING DRY FAN unable to set room temperature Turning on Press button, when the appliance receives the signal, the RUN indicator of the indoor unit lights up. 13 4 2 ONLY Operation modes *Note: Heating mode is NOT available for cooling only models. SWING, SMART, TIMER, SLEEP and SUPER operation modes will be specified in the following pages. Changing modes during operation, sometimes the unit does not response at once. Wait 3 minutes. During heating operation, air flow is not discharged at the beginning. After 2 -5 minutes, the air flow will be discharged until temperature of indoor heat exchanger rises. Wait 3 minutes before restarting the appliance. 7 PDF created with pdfFactory Pro trial version 5 Airflow direction control Vertical airflow is automatically adjusted to a certain angle in accordance with the operation mode after turning on the unit. The direction of airflow can be also adjusted to your own requirement by pressing the "SWING" button of the remote controller. Operation mode Direction of airflow COOLING, DRY *HEATING, FAN ONLY horizontal downward Vertical airflowcontrol (with the remote controller) Using remote controller to set various angles of flowor specific angle as you like. Swinging airflow Pressing "SWING" button once, the vertical adjustment louver will swing up and down automatically. Desired direction airflow Pressing the "SWING" button again when the louvers swing to a suitable angle as desired. Horizontal airflow control (with hands) Turning the control rods of the horizontal adjustment louvers to change horizontal air flow as shown. control rods of horizontal adjustment louvers Note: The shape of the unit may look different fromthat of the air conditioner you have selected. Do not turn the vertical adjustment louvers manually, otherwise malfunction may occur. If that happens, turn off the unit first and cut off the power supply, then restore power supply again. It is better not to let the vertical adjustment louver tilt downward for a long time at COOLINGor DRY mode to prevent condensed water fromdripping. Operation instructions 8 *Heating mode is only available for heat pump models. Airflow direction control SMART SLEEP SUPER 5 PDF created with pdfFactory Pro trial version Operation instructions SMART mode Press the SMART button, the unit enters smart mode(fuzzy logic operation) directly regardless of the unit is on or off. In this mode, temperature and fan speed are automatically set based on the actual room temperature. Operation mode and temperature are determined by indoor temperature Heat pump models Indoor temperature Operation mode Target temperature 21. or below HEATING 22 2222 . .. 21.-26. DRY Room temperature decrease 1.5. after operate for 3 minutes Over 26. COOLING 26. Cooling only models SM ART SLEEP SU P ER Indoor temperature Target temperature 26.or below 26.Over 26. Operation mode DRY Room temperature decrease 1.5.after operate for 3 minutes COOLING SMART button is ineffective in SUPER mode. Note: Temperature, airflow and direction are controlled automatically in SMART mode. However, a decrease or rise of up to 2 . can be set with the remote controller if you still feel uncomfortable. High High High High Low Low Low Low Your feeling A decrease or increase up to 2can be set in SMART mode. button adjustment procedure A rise up to 2can be set. A decrease up to 2can be set. Uncomfortable because of unsuitable air flow volume. Uncomfortable because of unsuitable flow direction. Press once to lower the set temp by1 Press twice to lower the set temp by2 Indoor fan speed alternates among High, Medium and Low each time thisbutton is pressed. Press i...
Эта инструкция также подходит к моделям:Кондиционеры - RIH-3267 (1.78 mb)