Оценок - 2, средний балл: 4
(
)
)
|
Фрагмент инструкции
2. If possible Install the unit where the sunlight does not shine directly on the unit. 3. The outside of the cabinet must extend outward for at least 12" and there should be no obstacles, such as a fence or wall, within 20" from the back of the cabinet, as it will prevent heat radiation of the condenser. Restriction of outside air will greatly reduce the cooling efficiency of the air conditioner. 5. Install the unit with the bottom about 30"- 60" above the floor level. Window Requirements NOTE: All supporting parts should be secured to sturdy wood, masonry, or metal. • This unit is designed for installation in standard double hung windows with actual opening widths from 22" to 36". • The top and bottom window sash must open sufficiently to allow a clear vertical opening of 15" from the bottom of the upper sash to the window stool. 10 Installation Kit Contents Type A:13EA (SCREW) 1 Type B:3EA (SCREW) 2 Type C:5EA (SCREW) 3 10mm16mm16mm Type D:2EA (NUT) 4 Type E:2EA (FRAME CURTAIN) 5 Type F:2EA (SILL SUPPORT) 6 Type G:2EA (BOLT) 7 10mm Type H:1EA (FOAM-STRIP) 8 Type K:2EA (FRAME-GUIDE) 9 Type L:1EA (WINDOWLOCKINGBRACKET) 10 Type M:1EA (FOAM-PE) 11 Type N:1EA (DRAIN JOINT PIPE) 12 Have the following tools available for installation: * Screwdriver (Slotted and Phillips) * Ruler * Knife * Hammer * Pencil * Level 11 12 ENGLISH PREPARATION OF CHASSIS 1. Remove the screws which fasten the cabinet at both sides and at the back. 2. Slide the unit out from the cabinet by gripping the base pan handle and pulling forward while bracing the cabinet. 3. Cut the window sash seal to the proper length. Peel off the backing and attach the Foam-PE to the underside of the window sash. 4. 5. 6. Insert the Frame guides into the bottom of the cabinet. Insert the Frame Curtain into the and Frame Guides. Fasten the curtains to the unit with 8 Type A screws. Shipping screws Foam-PE Upper guide Screw (Type A) Screw(Type A) Frame guide Fig. 1 Fig. 2 Fig. 3 Fig. 4 Suggested Tool Requirements SCREWDRIVER(+, -), RULER, KNIFE, HAMMER, PENCIL, LEVEL Upper Guide 0F Power Mode Timer 0n/0ff Fan Speed Temp Cool Money Saver® Fan Only Dry hr Auto Swing 0F Power Mode Timer 0n/0ff Fan Speed Temp Cool Money Saver® Fan Only Dry hr Auto Swing (Fig .1) (Fig .2) (Fig .3) (Fig .4) (Fig .4) (Fig .4) 1 1 9 Upper Guide Window stool Cabinet Installation 1. Open the window. Mark a line on center of the window stool.Carefully place the cabinet on the window stool and align the center mark on the bottom front with the center line marked in the window stool. (Fig. 1) Upper Guide Window stool Cabinet Installation 1. Open the window. Mark a line on center of the window stool.Carefully place the cabinet on the window stool and align the center mark on the bottom front with the center line marked in the window stool. (Fig. 1) 2. Pull the bottom window sash down behind the Upper Guide until they meet. NOTE: Do not pull the window sash down so tightly that the movement of Frame Curtain is restricted. 3. Loosely assemble the Sill Support using the parts . (Fig. 3) (Fig. 2) Front Angle Fig. 1 Fig. 2 4. Select the position that will place the Sill Support near the outer most point on sill. (Fig. 4) NOTE: Be careful when you install the cabinet (Frame Guides are broken easily). 5. Attach the Sill Support to the cabinet track hole in relation to the selected position using 2 -type A screws in each support. ( Fig. 4). 1 Fig. 3 Fig. 4 5 6 6 9 6 Window Sash Upper guide Frame Curtain Foam-PE Foam-PE Cabinet 11 5 ROODTUOROODNISill Support NutBolt 647 ROODTUOROODNICabinet About 1 / 2" Frame Guide Screw(Type A) 9 13 14 Sash track Front Angle About 1/2" Screw(Type B) Screw(Type B) Sill Support Sill Support Foam-Strip Fig. 5 Type C Fig. 6 Fig. 8 6. The cabinet should be installed with a very slight tilt (about 1/2") downward toward the outside (See Fig. 5). Adjust the bolt and the nut of Sill Support for balancing the cabinet. 7. Attach the cabinet to the window stool by driving the screws [Type B: Length 16mm (5/8 inch) and below.] through the front angle into window stool. 8. Pull each Frame Curtain to each window sash track, and repeat step 2. 9. Attach each Frame Curtain to the window sash using screws (Type C). ( Fig. 6) CAUTION: Do not drill a hole in the bottom pan. The unit is designed to operate with approximately 1/2" of water in bottom of pan. There is no need to add water if the pan is dry. 10. Slide the unit into the cabinet. ( Fig. 7) CAUTION: For security purposes, reinstall the 2 screws (Type A) at cabinet's side, that were removed in step 1 on page 12. 11. Cut the Foam-Strip to the proper length (window width) and wedge between the upper window sash and the lower window sash. ( Fig. 8) (Fig. 5) (Fig. 5) 6 2 6 2 5 2 6 3 5 3 8 8 Fig. 7 Screw(Type A) Screw(Type A) Power cord 0F Power Mode Timer 0n/0ff Fan Speed Temp Cool Money Saver® Fan Only Dry hr Auto Swing 1 1 15 Window locking bracket Fig. 9 Fig. 10 12. Attach the Window Locking Bracket with a Type C screw . ( Fi...