Оценок - 2, средний балл: 4.5
(
)
)
|
Фрагмент инструкции
The socket outlet that the system plugs into shall be installed near the equipment and shall be easily accessible. Pre-setup safety steps Whenever you remove the chassis panels to access the inside of the system, follow these steps: 1 Turn off all peripheral devices connected to the system. 2 Turn off the system by pressing the power button. 3 Unplug all AC power cords from the system or from wall outlets. 4 Label and disconnect all cables connected to I/O connectors or ports on the back of the system. 5 Provide some electrostatic discharge (ESD) protection by wearing an antistatic wrist strap attached to chassis ground of the system— any unpainted metal surface—when handling components. 6 Do not operate the system with the chassis panels removed. After you have completed the six steps above, you can remove the chassis panels. To do this: 1 Unlock and remove the padlock from the back of the system if a padlock has been installed. 2 Remove and save all screws from the panels. 3 Remove the panels. For proper cooling and airflow, always reinstall the chassis panels before turning on the system. Operating the system without the these panels in place can damage system parts. To install the chassis panels: 1 Check first to make sure you have not left loose tools or parts inside the system. 2 Check that cables, add-in boards, and other components are properly installed. 3 Attach the panels to the chassis with the screws removed earlier, and tighten them firmly. 4 Insert and lock the padlock to the system to prevent unauthorized access inside the system. 5 Connect all external cables and the AC power cord(s) to the system. Hardware setup The server is shipped without processors, memory, or hard drives. To install the memory, processors, hard drives, and other options, follow the steps shown below. 1 Removing the system access panels: a Removing the rear access panel - see page 44 b Removing the access cover to the system boards - see page 51 2 Removing the memory and processor boards: a Removing the memory board - see page 52 b Removing the processor board - see page 54 3 Installing memory and processors: a Installing the DIMMs on the memory board - see page 60 b Installing the processors on the processor board - see page 64 4 If you are installing an ICMB board - follow the instructions that came with the ICMB board kit. 5 Installing the processor and memory boards: a Installing the processor board - see page 54 b Installing the memory board - see page 52 6 Installing PCI add-in cards - see page 67 7 Installing hard disk drives - see page 78 8 Installing an additional power supply or additional peripherals see page 84, page 96, and any additional documentation that came with the peripherals. 2 System setup Reinstalling the system access panels: a Installing the access cover to the system boards - see page 52 b Installing the rear access panel - see page 45 You have completed the hardware setup. The remainder of this section discusses software setup and configuration. Refer to page 36. Turning on the server and running the Power-On Self Test (POST) Each time you start the server, the Power-On Self Test (POST) runs automatically. POST is stored in flash memory. To start the server, do the following: Note: To access certain features, such as BIOS setup, you must press specific keys at specific times during POST. To familiarize yourself with this procedure, read the following instructions completely before actually performing them. For a summary of hot keys active during POST, see page 35. 1 Make sure all external devices, such as a monitor, keyboard, and mouse, are connected. 2 If a drive protection card or diskette is present in the diskette drive, remove it. 3 Plug the video monitor power cord into the power source or wall outlet. Turn on the video monitor. 4 Plug the AC power cords into the power connectors on the back of the chassis and into the power source or wall outlet. 5 If the server does not turn on when you plug it into the AC outlet, press the on/off power button on the front panel. 6 Verify that the main power LED on the front panel is lit. After a few seconds, POST begins and a splash screen is displayed (if the splash screen is disabled in BIOS setup, a diagnostics screen is displayed). POST discovers, configures, and tests the processors, memory, keyboard, and most installed peripheral devices. The length of time needed to complete POST depends on the amount of memory installed and the number of option boards installed. 7 Shortly after the splash screen is displayed, POST displays the message "Press