Войти:
Оценок - 1, средний балл: 5 ( )

Инструкция по эксплуатации Fujitsu, модель PRIMERGY B120

Производитель: Fujitsu
Размер: 1.86 mb
Название файла: 9f7ab415-0a85-4772-8979-8b1fefb7e221.pdf
Язык инструкции:en
Перейти к скачиванию



Фрагмент инструкции


Guide the cable through the cable routings of the rack. 3.6 Prepare the keyboard E Plug the appropriate connector of the keyboard cable into the socket on the underside of the keyboard as shown in the illustration above. A26361-K646-Z102-1-7619 Connecting devices to the server Installation A26361-K646-Z102-1-7619 21 3.7 Connecting devices to the server All ports are on the rear of the server. Which ports are available on your server depend on the boards installed. The standard ports are marked with symbols and some are color-coded. 7 6 3 4 5 2 1 Tower 7 6 5 4 3 2 1 Rack 1 = Mouse 2 = Parallel interface (burgundy) 3 = LAN 4 = Monitor (blue) 5 = Serial interface 1 (teal or turquoise) 6 = USB (black) 7 = Keyboard (violet) E Connect the data cables at the server and peripherals. i Some of the devices that you connect require special drivers (see the documentation for the connected device). E Mark the lines so that you can always identify them. Installation Connecting devices to the server If you connect the monitor power cable to the monitor power outlet of a server with the ! standard power supply, then the current consumption of the monitor may not exceed 1.5 A (at 230 V) or 3 A (at 115 V). The rated current for the monitor is also given on the monitor itself or in the Operating Manual for the monitor. When connected to an uninterruptible power supply (UPS) the monitor must also be taken into account. Guide the cables through the cable routings of the rack. A26361-K646-Z102-1-7619 4 Preparation for use and operation ! i Please take note of the safety information in the chapter "Important notes". Work steps which are identical for the tower and rack version are only described for the tower version. For details on the rack variant, please see the Technical Manual for the rack. 4.1 Unlocking/locking the tower server Enabling access to the accessible drives 3 1 2 E Unlock the server (1). E Slide the drive cover downwards (2). E If you wish to prevent access to the hard disk drives, then lock the server again (3). Now the drive cover cannot be pushed into the top position and the hard disk cover cannot be removed. A26361-K646-Z102-1-7619 Preparation for use and operation Unlocking/locking the tower server 24 A26361-K646-Z102-1-7619 Enabling access to the hard disk drives 4 3 2 1 E Unlock the server (1). E Slide up the drive cover as far as possible (2). E Remove the hard disk cover toward the front (3 + 4). The hard disk cover is remounted and the server connected in the reverse order. Operation controls Preparation for use and operation 4.2 Operation controls 6 4 7 5 2 1 3 8 9 7 4 6 5 21 3 9 8 1 = Floppy disk drive with power-on indicator 5 = IDE busy indicator 2 = CD-ROM drive with power-on indicator 6 = Message indicator 3 = Lock 7 = ON/OFF switch with power-on indicator 4 = Chipcard reader with power-on indicator 8 = Hard disk indicator (optional) (optional) 9 = Hard disk error indicator (optional) A26361-K646-Z102-1-7619 Preparation for use and operation Operation controls 4.2.1 Operation controls Lock unlocks or locks the server. ON/OFF switch switches the server to ready-to-operate or on. The ON/OFF switch and the main switch do not disconnect the server from the line voltage. To disconnect the line voltage completely, remove the power plug from the socket. 4.2.2 Indicators Power-on indicator lights green when the server is switched on. IDE busy indicator lights green when an IDE drive is being accessed. 4.2.3 Drive indicators Hard disk indicator Lights when the hard disk drive in this slot is being accessed. Hard disk error (only in conjunction with disk array controller) lights, when the hard disk drive in this slot is defective and needs replacing. It is possible, that the drive is not correctly inserted. flashes when a rebuild is carried out by the disk array controller after a drive has been exchanged. CD-ROM drive indicator The indicator lights up when the CD-ROM drive is accessed. Floppy disk drive indicator The indicator lights up when the floppy disk drive is being accessed. A26361-K646-Z102-1-7619 Switching the server on and off Preparation for use and operation 4.3 Switching the server on and off If after switching on the server there is nothing but flickering stripes on the screen, switch ! the server off immediately (see "Troubleshooting and tips"-"Flickering stripes on the monitor screen"). The ON/OFF switch and the main switch do not disconnect the server from the line voltage. To disconnect the line voltage completely, remove the power plug from the socket. 0 I c a a c 0 I b b A26361-K646-Z102-1-7619 Preparation for use and operation Switching the server on and off Server is switched off The main switch (a) is in position 0 and the power-on indicator does not light. The ON/OFF switch (b) is inoperative. The screen socket on the server is dead. Server is ready for operation (stand-by state) The main switch (a) is in position I and the power-on indicator (c) does not light. The server can be s...

Эта инструкция также подходит к моделям:
Компьютеры - PRIMERGY B120 (1.86 mb)

Напишите ваш отзыв об устройстве



Текст отзыва
Ваше имя:
Введите две цифры:
capcha





Категории